- Home
- 1066667621
- Instructions
1066667621 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Maker wasn't working
2 of 3 people
found this instruction helpful.
-
F George from Lakeland, FL
- Really Easy
- 15 - 30 mins
-
Socket set
it was very very simple, it took only three screws
using socket set.
I removed the old one and put the new one in place , connect electric connection in 2 seconds snapping it toghether, that is all to it.
the hardest part is waiting on the ice to be made , which it took three to four hours for the first batch.
I am in ... Read more the medical profession, IF I CAN do it , everyone CAN!!!!!!!!
using socket set.
I removed the old one and put the new one in place , connect electric connection in 2 seconds snapping it toghether, that is all to it.
the hardest part is waiting on the ice to be made , which it took three to four hours for the first batch.
I am in ... Read more the medical profession, IF I CAN do it , everyone CAN!!!!!!!!
Read less
Was this helpful?
Thank you for voting!
old ice maker didn't work
2 of 3 people
found this instruction helpful.
-
Peter from SKANEATELES, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
3 screws and plugged in the new ice maker. It was slightly difficult to unplug the old ice maker and place the plug in the new ice maker. Still really easy. New ice maker works great!
Was this helpful?
Thank you for voting!
The refridgerator will not run
2 of 3 people
found this instruction helpful.
-
Victor from Colton, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
After the front panel was removed, disconnected the timer and installed new in reverse order. The provided instructions could be more straight forward, I spent more time reading it than the installation itself.
Was this helpful?
Thank you for voting!
Outer case of freezer was heating up, not making ice (sometimes) turned up thermostat several times (especially freezer)
3 of 6 people
found this instruction helpful.
-
John from Greensboro, NC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right
... Read more
direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.
Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well
Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well
Read less
Was this helpful?
Thank you for voting!
Refrigerator was freezing up and not cooling fresh food compartment
2 of 3 people
found this instruction helpful.
-
Greg from McLoud, OK
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
The repair was easy, I removed the cover on the top front of the fresh food compartment. It housed the defrost timer which was easy to identify and replace. Just removed a screw, unplugged the wires and replaced with the new part. Unfortunately, that wasn't the only problem. I also had to replace the defrost element that the timer sen
... Read more
t power to. While I was at it, I replaced the defroster thermostat. The entire repair took under an hour, diagnosing the problem took the most time and effort.
Read less
Was this helpful?
Thank you for voting!
3 months out of warranty - ice maker quit making ice
2 of 3 people
found this instruction helpful.
-
Lloyd from Tomball, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
unscrewed 4-5 screws; unplugged; attached arm; installed; reverse pattern. truly easy. cost 1/3 what repair man quoted me. this is easy!
Was this helpful?
Thank you for voting!
Old ice maker had cracked casing and was loosing teflon coating from cube tray
1 person
found this instruction helpful.
-
william from kansas city, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Followed instructions from online video. Used the opportunity to clean the freezer compartment really well. Also discovered that water solenoid valve was failing and have since replaced that also.
Was this helpful?
Thank you for voting!
Ice maker was not working.
1 person
found this instruction helpful.
-
GREGG from WEST CHESTER, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver
Ordered new single outlet water valve, received in less than two days. Removed old one, and the repair pretty much feel in place. Instructions were there as a backup. ........ Just curious if the connection from the water source to the valve outlet connection could b a quick connect just the like the water line going directly to the ice
... Read more
maker. Gregg in PA.
Read less
Was this helpful?
Thank you for voting!
Ice maker was leaking, and running too long (overflowing)
1 person
found this instruction helpful.
-
John from LAUDERHILL, FL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
While it probably could have been remedied with the controller, the cost difference between the controller and the unit made me opt for the entire unit. The fridge is a side by side, which meant in order for me to see the screws I'd need to use a mirror. Once I got the socket on the nut, it wasn't difficult to back out the upper screws. T
... Read more
he lower was a bit easier. The power cable however was frozen from years of attachment, and really defied removal. Once removed, the unit came out easily. In my case, the wires had to be removed from the old unit and reinstalled in the new. Not a big deal, but just another step. the issue I had was upon re-installation. The wire harness didn't want to reassemble, and since I could only fit one arm inside, it was difficult to get the connector attached and tightened. I was able to get a pair of channel locks across the connector and get it together. Once that was done I hung the unit back on the upper screws, verifying the fill tube was properly set. I then re-tightened the lower screw. I then turned on the water and it seemed to take a very long time before the unit actually filled with water. It's now been several hours and the ice is starting to once again collect in the bucket.
Read less
Was this helpful?
Thank you for voting!
Freezer made lots of Ice and Refrigerator didn't cool
4 of 10 people
found this instruction helpful.
-
Cecelia from Garden City, TX
- Really Easy
- 30 - 60 mins
-
Screw drivers
The Defrost Timer is located in Refrigerator section (not the freezer) where your temperture guages are. Move panel and replace the non working Defrost Timer with the new one. It took my husband about 30-40 mins to fix. This was about 2 weeks ago and my Freezer and Refrigerator are working like new. I bought this Kenmore Reftigerator bran
... Read more
d new in 1996 and I lost the manuel to it. Thanks to my daughter who found the Defrost Timer on the Internet, I thought I was going to have to buy a new one. This was real easy to fix. The instructions that came with the part was easy to understand and very self explanatory. It also had very good diagrams to follow.
Read less
Was this helpful?
Thank you for voting!
original motor stopped
2 of 4 people
found this instruction helpful.
-
Paul from Lowell, MI
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Socket set
removed old and instaslled new. biggest problem was getting to one of the screws.
Was this helpful?
Thank you for voting!
The old ice maker water valve washer in the water inlet port went bad and was leaking. Lasted for 35 years,
1 person
found this instruction helpful.
-
Edwin from Mount Washington, KY
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
The Whirlpool water inlet valve was better design than the original. All I had to do was drill 2 holes to mount it since it didn't mount in the same location as the old one. I liked the push in connection for the water outlet to the ice maker better than the original plastic screw connection.
Was this helpful?
Thank you for voting!
Warm refrigerater
1 person
found this instruction helpful.
-
charles from REDDING, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Followed instructions from ideoo
Was this helpful?
Thank you for voting!
Freezer no longer frost free.
1 person
found this instruction helpful.
-
anthony from NORCROSS, GA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Reviewed Youtube video as a reference. Unplugged refrigerator. Removed old defrost timer. Matched the color of the wiring harness to the diagram that came with the part. Attach new part to wiring harness.
Was this helpful?
Thank you for voting!
We would come home from wintering in Texas and the ice maker would again work for about a week. Decided to replace the valve because it wasn't expensive.
1 person
found this instruction helpful.
-
Tom from MINNEAPOLIS, MN
- Really Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
Replaced the valve and cleaned all the coils at the same time. The ice maker is spewing out ice. Wife is happy again.
Was this helpful?
Thank you for voting!