1066021 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer occasionally had a temperature alarm.Clicking noise also.
1 person
found this instruction helpful.
-
Barry from FORD CITY, PA
- Really Easy
- Less than 15 mins
Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.
Was this helpful?
Thank you for voting!
Plugged it in.
1 person
found this instruction helpful.
-
Adam from GLOVERSVILLE, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this helpful?
Thank you for voting!
handle broken
1 person
found this instruction helpful.
-
Laura from LAS VEGAS, NV
- Really Easy
- Less than 15 mins
-
Screw drivers
1. unscrew the two screws on the top of the broken handle and remove.
2. position the new handle into place by positioning the screw midway down the fridge into the groove thingy of the new handle
3 rescrew those screws in
4 tell your kid to stop slamming the fridge door shut
2. position the new handle into place by positioning the screw midway down the fridge into the groove thingy of the new handle
3 rescrew those screws in
4 tell your kid to stop slamming the fridge door shut
Was this helpful?
Thank you for voting!
freezer and refrigerator compartments not cold enough
1 person
found this instruction helpful.
-
Michael from Colorado Springs, CO
- Really Easy
- Less than 15 mins
-
Nutdriver
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 people
found this instruction helpful.
-
Carolee from Spokane Valley, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!
freezer would not freeze
1 person
found this instruction helpful.
-
Michael from HELENDALE, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thic
... Read more
k. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
Read less
Was this helpful?
Thank you for voting!
freezer became frosty but refrigerator's camera didn'thave any coll at all.
1 person
found this instruction helpful.
-
Yakov from BROOKLYN, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
After describing my problem PartSelect consultant emmidiately diagnost the problem and I ordered Evaporator Fan Motor. Along with purches order confirmation I got video how to install a new motor.
The hardest part was to connectthe ground wire becase space in that area was verylimited. Otherwise it was just like a walk in the park. ... Read more r />As soon as I installed motor and turned on the refrigirator, everything start working properly.
Thank you PartSelect, you sved me hundreds of dollars.
The hardest part was to connectthe ground wire becase space in that area was verylimited. Otherwise it was just like a walk in the park. ... Read more r />As soon as I installed motor and turned on the refrigirator, everything start working properly.
Thank you PartSelect, you sved me hundreds of dollars.
Read less
Was this helpful?
Thank you for voting!
no airflow to fresh food compartment or to freezer compartment....eveporator fan not working
1 person
found this instruction helpful.
-
Herbert from Pocono Lake, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Remove screws on the rear wall of the freezer. Pull the rear wall out and this gives you access to the evaporator fan assembley. Remove wires to the fan and to the defrost element to be able to move the rear wall to a position where you can work on the evaporator fan motor. The fan motor is held into place by a plastic bracket that c
... Read more
lips onto the reverse side of the freezer rear wall. Careful not to break the plastic clips that hold the fan in place as they are brittle. The fan blade friction fits on to the fan motor shaft and is a little difficult to remove. Assemble in reverse order.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Not enough cold air in refrigerator
1 person
found this instruction helpful.
-
RICHARD from VENICE, FL
- Easy
- 30 - 60 mins
Remove food from freezer shelf and ice maker back panel4 screws remove old motor replace with new motor reinstall all removed parts. Plug in and fan instantly came on refrigerator working great since
Was this helpful?
Thank you for voting!
door Shelf end cap was broken
1 person
found this instruction helpful.
-
Leora O from PIERZ, MN
- Very Easy
- Less than 15 mins
I just snapped it into place. Easy Peasy!!!!
Was this helpful?
Thank you for voting!
No cold
1 person
found this instruction helpful.
-
Jacqueline from LEXINGTON PK, MD
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
Like you video
Was this helpful?
Thank you for voting!
Track on pull out door cracked
1 person
found this instruction helpful.
-
Linda from MONTESANO, WA
- Very Easy
- Less than 15 mins
Sent model #..all of maytag parts have part # printed on them..snaps off and new part snaps on!!! Great!! They do have assistance to help you repair,but wasn't needed..i know who to order from now for any appliance!!
Was this helpful?
Thank you for voting!
Fan was not spinning make it not cold in bottom part
1 person
found this instruction helpful.
-
Dylan from WHEELING, WV
- Very Easy
- Less than 15 mins
-
Screw drivers
Take screws out pull panel out unconnect the part connect new one and your done
Was this helpful?
Thank you for voting!
Surface Element switch faulty with no control on heat
1 person
found this instruction helpful.
-
Ramiro from AUSTIN, TX
- Very Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Turned power completely off. Removed knob from front panel. Opened range top cover. Removed 3 screws from aluminum panel protector behind the element switch. Once panel is removed you can see the switch element. Remove 2 screws from the front panel that connects to the element switch. Remove the old element and replace with new element ma
... Read more
king sure that each of the 5 wires on the old element is transferred one by one to the new element. Reverse the process in putting it all together. Turn on the power and walla you've have a new stove. You just save $600 plus.
Read less
Was this helpful?
Thank you for voting!
drawer guide for drawer in refrigerator broke
1 person
found this instruction helpful.
-
Betty from MONROE, MI
- Really Easy
- 15 - 30 mins
empty top shelf in refrigerator, remove glass shelf. Wash and dry. Turn shelf over and line up notches and snap in place. Cost of guide plus 7.99 shipment fee and local ta was $18. Local dealer wanted $24 to order same part. Easy do-it-yourself project.
Was this helpful?
Thank you for voting!