10658582891 Kenmore Refrigerator - Instructions

I had a technician called out to the house to look at repairing several appliances that all have broken parts after just 3 yrs of use. Hood, Microwave, Oven, Fridge all in need of minor repairs..

Anyway - the estimate was $240 to replace the ice maker. I ordered PS358591 for $104. and it came in a couple days.. I took out one screw - slid out the icemaker, unplugged it - plugged in new one and slid it in the slot - and done !! Took about 20 mins.. didnt need any of the wiring harnesses in the box from partselect. Was way to easy to do !!

Thank you !

First, I unplugged the power to the entire fridge, and then removed the ice tray and ice door. Next, I unplugged the flat plug in the very back left behind the icemaker. Then I removed the 1/4" hex head sheet metal screws (2) and the phillips head screw (1) that hold the icemaker to the left side of the freezer wall. New icemaker came with a different style trip arm, so I used it. Plugged new icemaker in before reattaching it with the same (3) screws. Replaced ice tray and door, plugged in fridge, and waited....Dumped its first batch of ice maybe a couple of hours later. Not much trouble-shooting is needed when the entire icemaker is as easy and relatively inexpensive to replace as this. Twenty minutes, max.

First I removed the bolt that holds the cover on the top hinge bracket. Then I removed all items from the shelves inside the door by lifting the shelves out and placing them on the counter. Next I removed the 3 screws holding the hinge bracket on, this disconnects the top of the door from the cabinet. Then I lifted the door off the lower cam, removed the screws that held the cam in place on the door and the lower bracket on the cabinet and replaced the cams. I smeared some Vaselene on the cams and placed the door back on the lower cam, reconnected the upper hinge and replaced the hinge cover. All done and it works great!

We weren't sure if the problem was in the Water Inlet Valve or in the Icemaker Control & Motor Assembly. The water in the door did work. We removed the Water Inlet Valve & tested it with an Ohm Meter. It tested good so we put it back in. We then ordered the Icemaker Control & Motor Assembly. When it arrived we installed it and waited a few hours but the icemaker still did not fill with water. We telephoned a parts store and were told the problem could be the thermostat or we could replace the whole icemaker. We replaced the whole icemaker.

It was easy to snap off the old shelf and snap in the new. The price was right. The part was right. If I need to, I'll be back.

Unplugged power cord from the wall outlet
I removed the back cover using a 1/4 nut driver. Removed the two wires, one went to the starter driver the other to the overload protection. Unplugged the part from the compressor.Plugged in new part and re-attached the two wires replaced cover and plugged in power back in to the wall outlet

It was simply a matter of removing the old filter housing unit by unscrewing 3 screws and unplugging the two water tubes. After re-insterting the water tubing and securing the housing unit "VOILA" good as new..It really was easy..

I have an old DIY home repair book and I saw that the ice maker repair wasn't hard, so I ordered the parts from Part Select. 1 day to arrive...super service. The site is very helpful with diagrams about the parts. The repair was a cinch...EXCEPT I forgot to unplug and got a little zap. The shelf pegs were a breeze because I had read other's stories about how to remove and replace on this site. Go try to do it...get a book at library if you need some direction.

I saved my Whirlpool Refrigerator (Model ET21GKXHN00) and learned a lesson. Don’t put off cleaning the refrigerant coils underneath the refrigerator. I replaced the refrigerator about 10 years ago and began to notice that the sound of this one running had changed slightly. I remembered that’s what happened to the first one just before it died. I removed the panel on the bottom front and saw that the refrigerant coils were covered with dust. It was really bad. I vacuumed them with the “radiator attachment” on the vacuum cleaner and plugged the refrigerator back in. It still didn’t sound right and I couldn’t feel the air blowing out like it should. So I rolled the refrigerator out and removed the back lower cover to see the compressor and the cooling fan. The fan was clogged with dust so I vacuumed that as well. But the fan wouldn’t spin freely by hand. The fan motor only had 3 screws holding it onto the plastic fan bezel and was easily removed by unsnapping the electrical connector on the motor. I removed the fan motor and tried to clean it with a few drops of WD40 on the shaft. But when I put it all back and plugged it in the fan just barely started turning. I unplugged the refrigerator and ordered the fan motor from PartSelect.Com (Item Number PS371043). The picture looked exactly like the motor that was in my refrigerator. I threw everything away in the refrigerator, cleaned it out and left it unplugged until the motor came. The motor arrived in a few days and it looked exactly like the one I had removed. It had the same electrical specifications stamped on the back and the electrical connector was the same and in the same location on the motor. I put the fan blade on the new motor and installed it exactly like the old one was. It only took 15 minutes or so and was very easy to install. When I plugged the refrigerator in the compressor started right away and so did the fan. It ran like a champ. In a few hours the refrigerator got cold and began to cycle on and off like normal and the fan blows like new. The sound is normal and the total running sound is quiet again like a new refrigerator. So for $84.67 I saved my $1300 refrigerator and learned not to neglect checking the build up of dust in the compressor fan section. I’m sure that’s what happens to most of the refrigerators people put out for trash pickup in front of their houses. The cause of the problem is when air flow is restricted across the refrigerant coils too much heat returns to the compressor and eventually causes the compressor to fail. I appreciate that we live in a time when you can order exactly what you need on the internet and make home repairs when you need to. Thanks Part Select for sending me the correct part. It’s nice to have milk and cold drinks again.

The first step was to go to PartSelect.com to find where the filter is located because that is not revealed in Whirlpool's Guide. This refrigerator came with the home I had just puchased so Iwas unfamiliar with the filter replacement. Th filter is on the grill at the bottom of the refrigerator. I followed the instructions helpfully printed on the replacement cartridge box which arrived in less than the 3-5 days acknowledged on my order.

Turn the filter handle 1/4 turn counterclockwise. Don't be timid. It was very tight (probably had not been replaced ever). Remove the filter from the handle that protrudes through the grill at the bottom of the front of the refrigerator.

Insert the new cartridge into the filter handle insert snugly until it goes no further and turn 1/4 clockwise.

The instructions on the replacement cartridge tell you to run the water for 5 minutes to remove air and sediment from the system. DO NOT skip this step. I was. I discovered a large amount of sediment after even three minutes of flushing. A 5-gallon pale will help. And don't forget to turn off the ice maker while you are flushing. Otherwise you will end up with ice cubes everywhere as you try to position the bucket under the water dispenser.

I took the old drawer out and replaced it with the new one!
I hooked a new door bin in the door for more room!

First I unplugged the frig, and turned offed the water and ice dispenser using the on/off panel switch. I removed the panel by inserting a small flat blade screwdriver at the bottom of the panel where the plastic studs locked the panel in place. By inserting a little upward pressure, the panel popped right ouff. The Micro Switch was very easy to remove and replace. Just make sure that the plunger on the ice dispenser makes solid contact with the switch when depressed.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Replaced the door cam on bottom of fridge door. ONE THING TO UNDERSTAND- THERE ARE 2 CAMS ON THE DOOR, LOWER AND UPPER, BUT THE UPPER CAM IS NOT LISTED ON THE "DOOR HARDWARE" DRAWING, ITS LISTED ON THE MAIN BODY DRAWING! BE SURE TO GET BOTH CAMS! (PARTSELECT COULD MAKE A NOTE THAT WHEN PEOPLE LOOK UP LOWER CAM, PUT A NOTE IN THERE SAYING Y0U NEED UPPER TOO!)So I had to order the upper cam later and install later. BUT it is quite easy to replace, unlike the video, I only needed 1 tool! The nut driver (electric screwdriver w nut driver head). Thanks -RF

My icemaker wouldn’t pop out the ice. I bought a used fridge from 2nd Time Around in Russellville AR which was the most horrible customer service experience of my life. They were supposed to have a 60 day warranty but didn’t follow through. After months of begging them, and knowing what part I needed, I just ordered it myself. It was so easy and quick and fixed my issue my husband said we should have done that months ago and avoided the hassle. It was worth the money to have the peace of mind. Now everything is perfect! All we had to do was remove the icemaker, take off the side with a screwdriver, replace the part and slide it back in. We had ice in hours! Shipping was quick (a couple days) the part was 30 dollars cheaper than other places I checked. We love it!