10655612400 Kenmore Refrigerator - Parts

This advanced refrigerator water filter utilizes Triple Filtration Technology to reduce a wide range of contaminants, including mercury, lead, and trace pharmaceuticals, ensuring cleaner and safer water for drinking and food preparation. Certified to meet NSF standards, it is designed to deliver high-quality filtration performance across ...Read morecompatible refrigerator models. The filter should be replaced every six months or after filtering approximately 300 gallons to maintain optimal contaminant reduction. A noticeable decrease in water flow from the dispenser may also indicate the need for replacement. Installation is quick and tool-free, and it is recommended to flush at least two gallons of water through the system before use.

The lower door closing cam is used in refrigerator doors, it can be located on the fresh food side or the freezer side. It helps hold the door open. This cam is made out of plastic, so it might crack or wear down over time. If your door will not open and close properly you may need to replace the door closing cam. To successfully install ...Read morethis part, you will need a 5/16 nut driver and a small flat blade screwdriver. Before you begin, unplug your appliance and disconnect the water supply. Lubricating this part may help with installation. This replacement part is sold individually. This part will fit both the left and right side of your refrigerator door. To make the repair, remove the top hinge cover, then the top hinge support. Lift the door from the bottom support and remove the old door cams. Replace the cams, using a little lubricant if necessary, and place the door back on the lower hinge support. Replace the top hinge support and your repair is complete!

The Door Cam is a black plastic part which helps the door pivot shut while keeping the door and hinge in proper alignment. Lubricating this part upon installation may help it move easier. It attaches onto the door hinge and should be replaced if broken or if there is noticeable damage. Refer to your model number and user manual to ensure...Read more this is the correct part for you. To do this repair you will need a 5/6 nut driver, a 5/16 socket, and a ratchet. For safety purposes, do not forget to turn off your appliance before making this repair. Note that this piece is black, and as per the manufacturer requires a new screw to mount the door cam which is sold individually. Please also note that this is the closing cam for the lower door, and the upper door cam is sold as a separate kit.

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

This manufacturer-certified Pan Slide Track allows the drawer to slide in and out. It measures roughly 12 inches in length If this track is damaged or missing, you won't be able to move the drawer properly. The slide attaches to the side wall of the fridge and can be placed on either side. Refer to your model number and user manual to ens...Read moreure this part is right for you. To make this repair, first, remove the snack pan and glass shelf. Slide out the track from its locking pins on the side of the glass shelf, and slide the new track into place by lining it up with the locking slots. Replace the shelf and crisper drawer. This repair is rated as very easy by our customers, taking less than 15 minutes to complete and requiring no tools.

This water inlet valve supplies water to your refrigerator’s ice maker and dispenser. It includes a valve, tubing, and a coupling. The pre-filter bracket connector must be purchased separately if required. Unplug the refrigerator and wear gloves for safe installation.

If ice is building up in your freezer or if your freezer is getting too warm on the defrost cycle you may need to replace the bi-metal thermostat.

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

This black cap covers the water filter.

This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and attach to the new.

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

Sold individually.