10654782801 Kenmore Refrigerator - Instructions

I took out the ice collection box and auger to get access to the three screws holding the ice maker assembly against the left wall of the freezer. You can use a screwdriver or a nut driver. I then unpluged the assembly and wiggled it loose from the water fill tube. I assumed that unplugging the unit would disable the water valve but I put a plastic tub under the fill tube just in case. I studied the assembly on the kitchen table for a few minutes before I disasembled it. After removing a snapon plastick cover I removed three or four screws on the gearbox and was able to pull and wiggle the parts apart. The heater contacts have rubber O rings so you have to be firm pulling the mould out of and into the gearbox mount. Make sure it is fully seated. On reassembly note that the ice kicking arm is notched so it fits into the gearbox only one way and it helps to have it in position when you screw the gearbox back on. I also found the plastic ice guide that fits on top of the mold a little awkward in snaping back together. Make sure its fingers space evenly with the ice kicking arms.

I removed the ice maker assembly from the freezer compartment (four nuts/ nut driver) and unplugged the wire harness. I discovered the nature of the problem and I went on the Internet to look for replacement parts expecting I'd have to buy the entire ice maker. When I found PartSelect.com I looked through the pictures of the parts available for my ice maker. I found the correct part quickly and easily. And having an acurate photo on the site, I was able to match all the key features of the mold I had with the one on the screen. I ordered the part, and installed it the day it arrived with just a Phillips screwdriver and a nut driver. It functions perfectly.

I looked at some online diagnostics info and the owner's manual. The "error code" blinking red light on the receiver unit (located adjacent to the ice bucket) indicated that the emitter/receiver units were faulty. I located the parts on the PartSelect website (their price was less than half of what they wanted on the Sears website) and ordered them. I didn't pay for the expedited shipping and still received the parts within two days of ordering. Powered down the refrigerator, three simple screws to remove each cover for the emitter and receiver, unplug the old units and pop in the new units, replace the covers for each unit, repowered the fridge and, voila, you've got ice. I completed the repairs in less than 10 minutes. Couldn't be happier with the price, the diagnostics links/info or the prompt service. Next time I have an appliance issue, my first stop will be this website.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

I unplugged the refrigerator, then I taped ice shield up to top of refrigerator and taped the little flap on the left side of the refrigerator to side wall then I unscrewed one screw on the right side that holds the plug cover, which was then removed. I then updid the little latches on the icemaker and pulled the old ice maker out far enough to unplug the connector, which was not easy, but did unplug. I then unscrewed the three screws with the nutdriver and attached the bottom cover to the new ice maker. I then slid the new icemaker far enough to connect the electrical connector, then slid the new icemaker in until it latched. I replaced the connector cover and untaped the two items that had been taped and pluged the refrigerator into the wall socket. The new icemaker has produced ice every since.

Removed food itmes on broken shelf. Removed old glass shelf cover. Removed broken shelf bracket. Installed new shelf bracket. Intalled new glass shelf cover. Replaced food items back on shelf

I removed the ice bucket,the gear is located under the ice bucket and engages when ice bucket sits on it and turns the tray for ice to fall in the shute,2 screws to remove and the gear comes off and I put the new one on and put the screws back,very easy to do, total time 5 minutes,repair man wanted to charge $114 for the part and $100 for labor,I did it all for $25 thru this site,I love this site,it gsaved me alot of money,thanks partselect.,

a simple replacement

The design of this refrigerator door (it's a side-by-side) is somewhat unbelievable. The door is designed to hold things, yet when you do the weight of the door wears out the lower door cams. The cams are designed to "complete the door closing", i.e. when you gently push on the door the cam mechanism takes over. When the cams wear, the door fails to close. Note to others - you may mistakenly think that the failure of the door to close is related to the seal; it is not.

The repair is quite easy; remove the upper cover, using a not driver (socket), then remove the upper door bracket. Make sure you hold the door or have someone else hold it. After the fasteners are removed gently lift up on the door and remove it from the lower cam assembly. You will see two plastic cam pieces; one on the lower bracket and one on the door. Both need to be changed to effectively "renew" the door closing mechanism. Once the cams are replaced the door can be reassembled to the refrigerator.

It was pretty easy to install. The most difficult part was trying to get my hands into the small area to work. I had to use both hands, one to push the release in and the other to pull the tube out. Once I did that, inserting the tube was easy and everything worked perfectly.

First I removed the icemaker from the freezer by removing two horizontal screws holding it to the side wall, and one vertical screw holding the front to a bracket coming off the side wall. Then I used a flat screwdriver to unlock the electrical plug. (After doing this, I realized that this wasn't necessary at all, and this part could have been changed just as easily without removing the icemaker.) On the front, there is a white cover with Ice Maker Plus. Use a flat screwdriver to unlock the tangs and remove the cover. There are three screws in the corners that once removed, will allow the motor assy. to be gently pulled straight out. On the back of the part, you will see many gold lands that the timer touches. I don't think there was anything wrong with my motor. I had two spots where the gold plating was worn off, so I suspect it was not making contact, and the whole process would stop. Slide the new part in place making sure the teeth on the gears line up (not a big deal), and secure with the screws. Install cover and you're done. Mine has been making ice like it was brand new.

Put new drawer in fridge.

Water was dripping out of top freezer door and had water under the refridgerator. I could hear a clicking noice from bottom of refrigerator every 3-5 minutes.
After removing back panel, I noticed the fan was running and the clicking seemed to be coming from somewhere around the compressor which was warm. I noticed on the site a simular problem had been submitted. It said to remove the start relay and if it rattled it was bad. I removed two wires from it ( it is connected onto the side of the compressor) then took a small screw driver to pry it away from the compressor. It not only rattled but had tiny pieces falling out. I ordered the part and replaced it in less than 15 minutes total and all is well.

I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.

Thank you
Curtis Hall

Removed plastic door over ice maker remove 4 screws and slide unit out after disconecting pull apart elect. Plug. Pop off side gear cover install on new and slide in, reconnecting electric plug as you go.