1065176 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No water to ice maker
2 of 2 people
found this instruction helpful.
-
Malcolm from HILL, NH
- Really Easy
- 30 - 60 mins
-
Nutdriver
Got resistance values from partselect. Coil was not in range. I remove rear cardboard cover,shut off water. Valve located on right side rear. Hoses are quick release. Unplug wire harnesses.
Was this helpful?
Thank you for voting!
The door switch was broken so the interior light would not come on.
2 of 3 people
found this instruction helpful.
-
Catherine from BROOMALL, PA
- Easy
- Less than 15 mins
-
Screw drivers
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and th
... Read more
e new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
Read less
Was this helpful?
Thank you for voting!
No ice
2 of 3 people
found this instruction helpful.
-
Alfred from LA PUENTE, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
6 screws removed and part replaced
Was this helpful?
Thank you for voting!
Freezer drawer light switch failure.
2 of 3 people
found this instruction helpful.
-
HARRY from FSTRVL TRVOSE, PA
- Really Easy
- Less than 15 mins
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into
... Read more
trim. Plug refrigerator into wall socket.
Read less
Was this helpful?
Thank you for voting!
Light switch on door broke
3 of 6 people
found this instruction helpful.
-
Donna from Oro Valley, AZ
- Really Easy
- Less than 15 mins
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Was this helpful?
Thank you for voting!
Replace water filter
4 of 9 people
found this instruction helpful.
-
Jeanne from COSTA MESA, CA
- Really Easy
- 30 - 60 mins
Open door and from appliance instruction book
Replace filter
Replace filter
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 people
found this instruction helpful.
-
Gail from Golden, CO
- Really Easy
- Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
Light out.
1 person
found this instruction helpful.
-
Carlton from CHICAGO, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Popped out the old switch and replaced it with the one dying
Was this helpful?
Thank you for voting!
Changed the filter
3 of 7 people
found this instruction helpful.
-
George from Port Orchard, WA
- Very Easy
- Less than 15 mins
Took the old one out and put the new one in
Was this helpful?
Thank you for voting!
Broke the bottom freezer door bin
1 person
found this instruction helpful.
-
David from ENGLEWOOD, FL
- Very Easy
- Less than 15 mins
The new bin slid right into the required slot
Was this helpful?
Thank you for voting!
No problems
1 person
found this instruction helpful.
-
Richard from PORT JERVIS, NY
- Very Easy
- Less than 15 mins
Just plugged it in
Was this helpful?
Thank you for voting!
Light rocker switch broke and refrigerator light couldn't go on.
2 of 4 people
found this instruction helpful.
-
Cathy from HOPATCONG, NJ
- Very Easy
- Less than 15 mins
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this helpful?
Thank you for voting!
Difficulty removing old switch.
1 person
found this instruction helpful.
-
Ronald from HUNTINGTN BCH, CA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Was this helpful?
Thank you for voting!
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
1 person
found this instruction helpful.
-
John from AUBURN, CA
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Was this helpful?
Thank you for voting!
Ice maker grinder motor was not running.
1 person
found this instruction helpful.
-
John from DUNNELLON, FL
- Really Easy
- 30 - 60 mins
-
Pliers, Socket set
Remove the ice bucket and check that the auger that turns in the ice bucket is free to turn. Cover the open freezer with cardboard or whatever to retain most of the freezer temperature. Remove the holder that supports the top of the motor shaft. Check the splines on the upper part of the motor shaft and also check the seal under the holde
... Read more
r. Open the access the door to the motor, remove wiring connector and unbolt the motor. Check the lower splines on motor shaft for condition, clean the shaft and apply new grease to the splines. Before installing, connect the wiring to the new motor, push the door switch in, press the ice dispenser arm outside the door to make sure the motor runs. If all ok, check the motor shaft for fit in the new motor. Be careful not to install the motor shaft too deep in the motor splines, otherwise there may not be enough spline showing on the top end to engage the auger. Bolt the motor in place, close access door and install the holder and ice bucket and make sure everything works. If there is not enough spline showing thru the holder to engage the auger, take pliers and pull the shaft up a bit. This seems to be a hit or miss fit on the shaft but you can adjust the height of the shaft without taking every thing apart again. That's all, not difficult at all. But do check parts and pieces for anything else you might need, parts wise, before ordering the motor by itself like I did. Shipping is high, so try to order any associated parts needed when you order the motor. By the way, This site are great to work with!
Read less
Was this helpful?
Thank you for voting!