1065176 Kenmore Refrigerator - Instructions

All Instructions for the 1065176
31 - 45 of 154

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced the front buttons due to wear
7 of 8 people found this instruction helpful.
  • Timothy from NAPERVILLE, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The plastic covering over the buttons for water and ice on our refrigerator door ice maker wore out after 4 years and looked bad. So instead of buying a whole new fridge we looked at replacing the panel. I found it here and ordered it. All it took to replace was a small flathead screwdriver to pop the old one out on the tab by the light. I figured out where it was by looking at the new unit. plugged in the new panel and it was good to go and easier than I thought it would be. Thank god because I thought my wife would never stop complaining about the refrigerator door buttons. ;)
Was this helpful?
Thank you for voting!
light not working in fridge
7 of 8 people found this instruction helpful.
  • Michael from East Meadow, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!
Was this helpful?
Thank you for voting!
The bin was broken
6 of 6 people found this instruction helpful.
  • Jordan from SPRINGFIELD, MO
  • Very Easy
  • Less than 15 mins
Lifted old bin up and pulled away from door. Took new bin, placed in door and set down in place. Replaced old broken bin with new bin. Added additional bin for more storage.
Was this helpful?
Thank you for voting!
Not making ice
6 of 7 people found this instruction helpful.
  • Janet from DOVER, DE
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
1 Remove ice tray
2 turn off ice maker
3 Remove 4 screws
holding on the
cover over the ice
maker
4 remove the two hex
screws holding in
the ice maker.
Remove ice maker.
5 Reverse this procedure for installation.
Was this helpful?
Thank you for voting!
Changed air filter
6 of 7 people found this instruction helpful.
  • Tom from LONGMONT, CO
  • Very Easy
  • Less than 15 mins
Very simple, easy, and quick! Anybody can do it!!
Was this helpful?
Thank you for voting!
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
7 of 10 people found this instruction helpful.
  • Antonio from San Antonio, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
Was this helpful?
Thank you for voting!
The Switch Broke...Absolutely Fell Apart.
5 of 5 people found this instruction helpful.
  • Duncan from Metairie, LA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Was this helpful?
Thank you for voting!
Lower Freezer worked fine, but upper refrigerator would not cool.
5 of 5 people found this instruction helpful.
  • Stephen from Jacksonville, FL
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
I first replaced the lower (freezer) evaporator thermistor based on recommendation from other feedback, however that did nothing to resolve the problem. I subsequently discovered a diagnostic document hidden under the upper right door hinge, which helped me narrow the problem down to the upper (refrigerator) evaporator fan motor. After r eplacing the fan motor, my refrigerator is up and running again. The only challenge was accessing and removing the access panel(s) and air column. Once those were removed, replacing the fan motor was simple.
Was this helpful?
Thank you for voting!
Raise side of fridge and slide 2x4 under side with broken wheel.
5 of 6 people found this instruction helpful.
  • Hans from OGDEN, UT
  • Really Easy
  • Less than 15 mins
  • Socket set
Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.
Was this helpful?
Thank you for voting!
air filter needed replacement
5 of 6 people found this instruction helpful.
  • David from Dublin, NH
  • Very Easy
  • Less than 15 mins
pulled the top shelf and poped open the door and replaced the filter
Was this helpful?
Thank you for voting!
POWER SURGE TOOK OUT THE POWER INVERTER
6 of 9 people found this instruction helpful.
  • David from GOWANDA, NY
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
ONCE WE KNEW THE COMPRESSOR WAS NO LONGER FUNCTIONING , USED A MULTI METER TO VERIFY 120 VOLTAGE TO THE INVERTER WAS PRESENT, FOUND 120 VOLTAGE TO THE INVERTER WITH NO VOLTAGE TO THE COMPRESSOR. OHMS OUT THE COMPRESSOR, FOUND IT WAS WITH IN SPECS. REPLACED THE INVERTER AND ALL IS WELL ONCE AGAIN.
Was this helpful?
Thank you for voting!
Ice maker quick working and made a clicking sound while trying to drop ice
5 of 6 people found this instruction helpful.
  • Thomas from HARPER, TX
  • Easy
  • 15 - 30 mins
  • Socket set
Removed freezer cover from ice maker, unplugged the harness. Installed the new ice maker assembly,plugged in two wire harness and secured the part and cover.
Results was smooth process, no noice from ice dispenser. Pleased with results. Saved on repairs. Thanks Tom
Was this helpful?
Thank you for voting!
Refrigerator light would not stay on
4 of 4 people found this instruction helpful.
  • Dave from Manchester Center, VT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
Was this helpful?
Thank you for voting!
My ice maker would only freeze for a short while, after unplugging it for a few hours it would begin to make ice again only to stop after a few trays
4 of 4 people found this instruction helpful.
  • Elizabeth from EDENTON, NC
  • A Bit Difficult
  • 30 - 60 mins
The repair went great, however, I had someone to put the part in for me.
Was this helpful?
Thank you for voting!
Broke the Rocker Switch in Fridge side
5 of 7 people found this instruction helpful.
  • Sung-Su from BISMARCK, ND
  • Very Easy
  • Less than 15 mins
Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.
Was this helpful?
Thank you for voting!
All Instructions for the 1065176
31 - 45 of 154