10651724410 Kenmore Refrigerator - Instructions

Jus took me seconds to replace both items. No problem.

Not being a professional repair tech, I looked at this sites provided schematics of the ice-maker. I assumed due to the problem I had which parts to order. the parts arrived within 3 days and after I took the icemaker apart I quickly realized I ordered the wrong parts. I called and asked what to do. since I did not open the packaging for the "wrong" parts I was able to make a return. I then called back because I discoverd the part I really needed wasn't shown in the sketch. I was told that I needed to order a new motor and it would have the part I needed. I ordered the part and within 3 days it arrived. Once I had the new part I was able to quickly install. Now I have a icemaker that works better than new since ,now it does not seem to jam either.

To make the repair:
First remove the 1/4" nut head screw on the under side of the ice maker.
Remove the shroud covering the electrical connection.
Slide out the maker and depress the locking clip.
Disconect the electrical wires.
Pull off the motor cover (no screws).
Remove the three philips head screws from the motor housing. Gently remove the motor.
Next loosen the screws and pull the "black motor-mounting harness" untill enough clearance to remove the ejector arm and deflector tray. The new kit will have a new ejector arm and deflector tray.
Insallation is the reverse.
The schematics were very helpfull.
It was very simple and I saved a $150 service fee to have someone else do it for me.
PS. When I called I was able to speak to real live Americans who were able to help me, were pleasant, polite, and professional, AND they did not treat me like I was stupid because I am not a professional repair man. I will definately use this service again. and recommend to all my DIY friends!!

Took out the old one and put in the new one. No tolls required. It did give me the opportunity to clean the back wall of the refrigerator.

When I took the pan out of the box, it was not the exact same as the one I had. But it fit perfect. The only hard part was the fact that it looked so good I had to clean the entire fridge side. (Smile)

After lots of internet exploring and diagnosis, the icemaker comes right out, and with three screws out and in, the job is all but done. Don't pay anyone for this repair!!!!!

removed old shelf support after taking out the glass and support. New part was a perfect fit that was a "shap: to put in.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

Refrigerator side top unscrewed hex screws unscrewed Phillips screws remove circuit board unplugged connects and installed new board in reverse order

Approximately:

1. Unplugged refrigerator.
2. Emptied Freezer.
3. Removed Ice Maker.
4. Waited a few hours for ice to melt around back panel & nuts.
5. Removed back panel and the cover over fan and fan motor.
6. Waited many more hours for ice to thaw over fins, wiring, etc.
7. Easily replaced the bi-mental defrost thermostat.
8. Replaced panel, fan cover, ice maker.
9. Plugged in refrigerator and waited a bit.

This worked! Yahoo.

p.s. I am a 65+ year old mechanically minded woman. :-)

Followed the u tube directions disconnect the power to the refrigerator remove the Ice cube pan place flat head screw driver under the front tabs push in to release the tabs pull down on the light release the back tabs from housing pull the light down from the housing disconnect the plug from the burned-out diode replace with the new diode light and repeat the same instructions in reverse to reinstall the diode light. The diode light in the freezer controls all the light in the refrigerator and freezer all should now light up.

Emptied draw of contents pulled draw out and inserted new drawer....easy pea-zee

I originally ordered the led light control board but when I hooked it up I still had the same problem. My neighbor checked both door switches with a voltmeter and they were both good. I then ordered the light for the freezer and when hooked up the problem was solved. All lights worked. The freezer light has four tabs that allow it to snap into the roof of the freezer. Those tabs can be hard to see because there isn’t much room. I used a mirror to locate the tabs and a small flat tip screwdriver to push the tab over and removed the light.

replaced

I removed the screws that attached the drum housing to the bin. I detached the auger & removed the broken drum assembly, turning the auger to the right, opposite what I thought it should be. I slipped the end of the auger into the new bin coupler & put it in place at the rear of the bin. Next I slipped the auger drum into place & tightened it to the left with a socket wrench. I screwed the drum housing to the bin, put the bin back into the freezer & I now have ice through the door again. Easy repair even for me, a 60+ woman.