1065172 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced cracked slide out glass shelf with new one
3 of 3 people
found this instruction helpful.
-
Michael from ROYSE CITY, TX
- Very Easy
- Less than 15 mins
Simply slid out damaged shelf and slid in new one
Was this helpful?
Thank you for voting!
Used a flat head screwdriver to pop the old light out.
4 of 6 people
found this instruction helpful.
-
Linda from MURFREESBORO, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
Plugged the new one in and snapped it into place. Only other need is a lantern or someone to shine a flashlight over your shoulder since the old light is, presumably, out.
Was this helpful?
Thank you for voting!
Shelf broke when I was trying to remove it.
3 of 3 people
found this instruction helpful.
-
Rebecca from ELYRIA, OH
- Really Easy
- Less than 15 mins
I ordered another shelf w glass. Put back in refrigerator and it fit perfectly.
Was this helpful?
Thank you for voting!
One of the shelves broke and needed to be replaced
3 of 3 people
found this instruction helpful.
-
Susan from Bloomington, IL
- Very Easy
- Less than 15 mins
It took less than one minute to open the box and place the shelf in the fridge!
Was this helpful?
Thank you for voting!
Auger would not turn properly
6 of 12 people
found this instruction helpful.
-
Tanya from Lakebay, WA
- Easy
- Less than 15 mins
I took out the ice bin and in the back where the auger meets the ice bin I had to replace the small plastic piece to hold the auger in place when using the automatic ice maker. It was an easy fix.
Was this helpful?
Thank you for voting!
ice container bin cracked and had a hole in it.
5 of 9 people
found this instruction helpful.
-
Joseph from MESQUITE, NV
- Very Easy
- Less than 15 mins
Took it out of the box. Emptied the ice out of the broken bin. Slid the new one in and all done.
Was this helpful?
Thank you for voting!
Drum broken; ice wouldn't dispense
3 of 3 people
found this instruction helpful.
-
Brenda from Downs, IL
- Really Easy
- Less than 15 mins
-
Nutdriver
1. Pull out drawer. 2. Remove screws to release the auger. 3. Unscrew the end of the auger. 4. Pull parts off. 5. Replace drum. 6. Replace parts in the correct order. 7. Twist end of auger back on. 8. Replace unit onto drawer and install mounting screws. 9. Place drawer in freezer. 10. Test ice dispenser. 11. Watch kitten run t
... Read more
o refrigerator and beg for ice cube. 12. See smiles on family members faces.
Read less
Was this helpful?
Thank you for voting!
Top half of freezer & fridge were not cooling. Freezer fan had been making unusually loud noises.
3 of 3 people
found this instruction helpful.
-
rich from PEMBROKE PNES, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver
Piece of cake. It took me longer to remove the food from the freezer, remove shelves and back panel than to do the repair. I heard the fan making some noises so I replaced both the fan and defrost thermostat. I used the instructions submitted by a another customer. My 20+ year old fridge is like new now.
Was this helpful?
Thank you for voting!
Water was not dispensing from the refrigerator.
3 of 3 people
found this instruction helpful.
-
Clifford Bell. from WASHINGTON, DC
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Installed a new water filter housing unit.
Was this helpful?
Thank you for voting!
Freezer work perfectly, Refrigerator Stopped getting cold, water line froze, there was ice Forming around the condenser in the bottom of the refrigerator behind the drawers
3 of 3 people
found this instruction helpful.
-
Richard from STATEN ISLAND, NY
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. ... Read more I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. ... Read more I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.
Read less
Was this helpful?
Thank you for voting!
Freezer was icing up and leaking. Refrigerator side would not keep cold.
3 of 3 people
found this instruction helpful.
-
Camille from Glen Ellyn, IL
- Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
We emptied out both sides, refrigerator and freezer, and followed the instructions in your video. We turned it off and disconnected the power. We took off the freezer door first. It made it much easier to get the shelves out and reach way back into the freezer. We removed the light and cover, then the ice auger motor. The back panel wa
... Read more
s easy to lift and remove. The wire assembly was a little hard to understand at first, but when we figured it out it was easy to remove and replace the bimetal defrost thermostat. We did check the video when we had the wire harness out, to make sure we got it right. We reassembled the freezer's inside parts and reattached the door. Before we turned the power back on, we scrubbed down the entire refrigerator. When we turned the power back on, the refrigerator and freezer were operating quietly - no sparks or explosions or shorting out - hooray! And the problems were solved.
The most important resource is your video. It looked like something we could do, and then ordered the parts. Our repair took a long time because we checked the video so many times. Thank you so much for the great information and the excellent parts. We could not have done it without you.
The most important resource is your video. It looked like something we could do, and then ordered the parts. Our repair took a long time because we checked the video so many times. Thank you so much for the great information and the excellent parts. We could not have done it without you.
Read less
Was this helpful?
Thank you for voting!
my drum was broken and would not put ice down to be used
3 of 3 people
found this instruction helpful.
-
Sue from Covington, GA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I could not have done it without reading the repair story about this same issue. I DID take a digital picture before taking the blades out and that was helpful. NO ONE, except in the repair story, ever mentioned the reverse screw to get the blades off. It simply made it possible for me.
I fixed it!!!! I am a 69 year old widow ... Read more who loves crushed ice, so I am happy!!
The PartSelect service is great!
I fixed it!!!! I am a 69 year old widow ... Read more who loves crushed ice, so I am happy!!
The PartSelect service is great!
Read less
Was this helpful?
Thank you for voting!
Auger Busted
3 of 3 people
found this instruction helpful.
-
Jan from Chandler, AZ
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Removed all ice from bin and let it thaw. Removed all screws and nuts from the front to release the ice crusher and the long bit. Had already printed out all the advice from others on the on-line section about taking photos and not getting the crusher blades out of order. Removed the clip with needle nose pliers and the washer. Re
... Read more
moved the blades laying them down in exact order and direction they came off. Put on the new auger drum and reversed everything. It was nice to know that the plastic screw that held the clip is a reverse thread, otherwise we might have broken the dang thing. Too bad there aren't instructions with the part when you get it instead of just a diagram. All-in-all, it went well.
Read less
Was this helpful?
Thank you for voting!
Part went bad the freezer was freezing up and refrigerator not getting cold
3 of 3 people
found this instruction helpful.
-
Jessica from WILLIAMSBURG, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
I pulled off the panel covering the part in the freezer cut and stripped the wires. Used crimper and connectors put the new part on put the wires band panel back on and plugged the refrigerator back in. Everything works just fine now.
Was this helpful?
Thank you for voting!
Ice bucket cracked and pieces broke off the bottom
4 of 6 people
found this instruction helpful.
-
Elizabeth from SANDY, UT
- Really Easy
- 15 - 30 mins
-
Screw drivers
I followed the video exactly, pausing it as I went along. So unbelievably easy! And Iām 78 year old great -grandma! Thank you
Was this helpful?
Thank you for voting!