1065112 Kenmore Refrigerator - Instructions

All Instructions for the 1065112
121 - 135 of 555

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
fridge stopped cooling then the freezer
4 of 4 people found this instruction helpful.
  • Joseph from DELTONA, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,
Was this helpful?
Thank you for voting!
The original gasket was breaking down and started to separate. The seal was starting to be compromised..
4 of 4 people found this instruction helpful.
  • Cathy from DOWNERS GROVE, IL
  • Really Easy
  • 30 - 60 mins
I ordered two new ones from partselect.com. I figured if I was replacing the one for the refrigerator door I might as well do the freezer door too.
Very easy to take the old ones off, take the putty knife clean tracks out. Putting the new ones on, was a little harder to do. You have to start in the corner and push the gasket into t he slot. You need strong hands to do this. Once I heard them click in, they guided themselves the rest of the way. Once they are on, check to make sure they touch the frame of the door. My freezer was perfect, but the refrigerator had an area of 25 inches that did not touch the frame. I called partselect.com and they sent out another new gasket for the refrigerator door. (I had to pay for this one but was told once I mailed in the defective one, they would credit me the cost of the returned one) I took off the bad gasket and installed the 2nd new gasket and that one was perfect.
Was this helpful?
Thank you for voting!
Gasket had become bad and letting air in which was causing an ice/water build up in freezer!
5 of 7 people found this instruction helpful.
  • Rod from BATON ROUGE, LA
  • Really Easy
  • 30 - 60 mins
Ordered gasket through this site pulled old gasket off, because my conquest had no screws on lining, Put new gasket on top and bottom first and kind of forced the edges into groove using heat gun cause gave me a little problem. But overall, it worked to perfection! Now to buy other gasket for refrigerator door!
Was this helpful?
Thank you for voting!
Lights not working some times
4 of 5 people found this instruction helpful.
  • Harry from COLUMBIA STA, OH
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Removed old switch and installed new - but did not solve problem
Was this helpful?
Thank you for voting!
When the filter was removed the housing leaked.
7 of 14 people found this instruction helpful.
  • Jeremy from SPRINGFIELD, TN
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
I would suggest loosening the supply lines attached inside the rear. This will give you plenty of slack to disconnect the lines from the housing.
Was this helpful?
Thank you for voting!
LED light in freezer not working
4 of 5 people found this instruction helpful.
  • Judith from RIDGWAY, CO
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Unplugged frig. With flat head screwdriver, removed light module and unplugged. Installed replacement module and snapped back into place. Replugged frig.
But did not work!! Repeated steps 2x, but no change.

Had been told the frig LED light was the same module as the freezer, but that is not the case. I had hoped to tr y the new module in the frig. So, back to square one and since I installed the new part, can't return!
Was this helpful?
Thank you for voting!
Ice would not come out of the despensor
4 of 5 people found this instruction helpful.
  • Ken from Cedar CVity, UT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Pulled out the ice bin and dumpted ice in the sink. Use 1/4 inch nut driver to take out all 1/2 inch screws. Be careful to watch how door spring and holder goes. Pull assembly apart and remove alger. Plastic nut on end of alger has reverse threads, remove it and then remove broken alger drum. Replace with new drum and reassemble in rever se order.
Was this helpful?
Thank you for voting!
Broken meat drawer
6 of 11 people found this instruction helpful.
  • Lionel from Escondido, CA
  • Really Easy
  • Less than 15 mins
This story is less about the repair than the service. On Monday, I removed the meat drawer to give it a quick rinse. Unfortunately, I fumbled the ball getting it back to the fridge, dropped the drawer on the hard stone floor, shattering it.

Instead of calling a repair man or going to the local appliance store, I opened up my ma cbook, found partselect.com, ordered the part and they had it taken care of in 5 minutes. Two days later, Fed Ex handed me a box with the replacement drawer, and I slide it in. Done. Total time to repair -- 6 minutes.

Sure beats leaving the house!
Was this helpful?
Thank you for voting!
Snack pan drawer was out when refrigerator door was closed. The snack pan drawer was cracked and needed to be replaced.
4 of 5 people found this instruction helpful.
  • Jack from Austin, TX
  • Really Easy
  • Less than 15 mins
Replacing the drawer was extremely easy. The refrigerator door need to be completely opened. Drawer slides out very easily and new drawer slides in where old drawer came out. Three minute job, tops.
Was this helpful?
Thank you for voting!
Old one leaks on one side
4 of 5 people found this instruction helpful.
  • Orlando from Bayonne, NJ
  • Very Easy
  • Less than 15 mins
Simply cut the water tube on both sides of connector and push in the new one.
Was this helpful?
Thank you for voting!
old filter was overdue for replacement
4 of 5 people found this instruction helpful.
  • gene from COTTONDALE, FL
  • Very Easy
  • Less than 15 mins
ordered new filter, removed old filter from fridge, and installed new one
Was this helpful?
Thank you for voting!
LED Light was out in freezer
5 of 8 people found this instruction helpful.
  • Victoria from SCARBOROUGH, ME
  • Very Easy
  • Less than 15 mins
Unplugged the old one and put in new one. So simple I didn’t need my husband’s help
Was this helpful?
Thank you for voting!
Broken shelf for snack drawer
4 of 5 people found this instruction helpful.
  • Kay from LA CRESCENTA, CA
  • Very Easy
  • Less than 15 mins
Slide drawer in and fit perfectly.
Was this helpful?
Thank you for voting!
needed another shelf
4 of 5 people found this instruction helpful.
  • Carol from JUPITER, FL
  • Very Easy
  • Less than 15 mins
slide right in. Easy
Was this helpful?
Thank you for voting!
Filter indicator light red
6 of 11 people found this instruction helpful.
  • Scott from ONEIDA, NY
  • Easy
  • Less than 15 mins
Found the filter door in toe kick under freezer door. Opening the door ejected the old filter. Direction indicator arrows were found on inside of filter door, rotation of filter to match arrows important. Pushed new filter in to stop, closing door completed insertion of new filter.
Was this helpful?
Thank you for voting!
All Instructions for the 1065112
121 - 135 of 555