1065111 Kenmore Refrigerator - Instructions

All Instructions for the 1065111
91 - 105 of 513

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The wrong filter was sent the first time.
8 of 11 people found this instruction helpful.
  • Sandra S from Topeka, KS
  • Difficult
  • 15 - 30 mins
I removed the cap from the filter pushed a lever and removed fliter. I replaced the old filter, removed the caps on the new one and slid it into channel after replacing the outer cap. I removed water from the spigot for 4 mins. and it was ready to go. I pushed the reset button to get the green light to come on.
Was this helpful?
Thank you for voting!
Icemaker Wouldn't Work
7 of 9 people found this instruction helpful.
  • NANCY from KEOKUK, IA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I removed the screws that attached the drum housing to the bin. I detached the auger & removed the broken drum assembly, turning the auger to the right, opposite what I thought it should be. I slipped the end of the auger into the new bin coupler & put it in place at the rear of the bin. Next I slipped the auger drum into place & ti ghtened it to the left with a socket wrench. I screwed the drum housing to the bin, put the bin back into the freezer & I now have ice through the door again. Easy repair even for me, a 60+ woman.
Was this helpful?
Thank you for voting!
Ice Maker would no longer move ice through the dispenser
8 of 12 people found this instruction helpful.
  • Sheila from Lena, MS
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
As cookbook authors and publishers, my husband and I depend on our appliances. When our icemaker would no longer work, it was imperative that we repair it as quickly and ecomonically as possible. We had used PartSelect.com earlier to order a part to repair our Jenn-Air stove top and had great results. So, rather than paying a repairman four times or more the cost of the part, we ordered the part and my husband installed it. It took less than 30 minutes to remove the broken auger and install the new one. THANKS PartSelect.com -- we'll use you for all appliance parts needs.
Was this helpful?
Thank you for voting!
broken drawer
8 of 12 people found this instruction helpful.
  • Thomas from North Port, FL
  • Really Easy
  • Less than 15 mins
replaced
Was this helpful?
Thank you for voting!
Water filter
10 of 18 people found this instruction helpful.
  • David from port st lucie, FL
  • Really Easy
  • Less than 15 mins
Just put the new one in.
Was this helpful?
Thank you for voting!
Crack in vegetable drawer
6 of 6 people found this instruction helpful.
  • Paul from NAYLOR, MO
  • Very Easy
  • Less than 15 mins
Emptied draw of contents pulled draw out and inserted new drawer....easy pea-zee
Was this helpful?
Thank you for voting!
Warm ref and frz
6 of 6 people found this instruction helpful.
  • Peter from MASSAPEQUA PK, NY
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Removed old starter and capacitor as per your website instruction.
Plugged in new parts.
Compresser turned on
Was this helpful?
Thank you for voting!
Stopped cooling/freezing
6 of 6 people found this instruction helpful.
  • Roper from PALM BAY, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
It is as easy as is shown in the self-help video. (1) Disconnect the power, (2) Roll the appliance out so you can get to the back, (3) Using a nut driver remove all the screws from the lower back panel then remove the panel, (4) Remove the tensioner wire, (5) unplug the electrical connection to the capacitor, (6) gently but firmly remove the capacitor and starter relay as one unit, (7) preassemble your new capacitor and starter relay as one unit, (8) now simply reverse your steps for installing and you are done! These two parts saved me the cost of a new refrigerator. Almost as easy as changing a light bulb. PS: while you have the panel removed you can do a thorough cleaning with a soft brush and vacuum.
Was this helpful?
Thank you for voting!
Ice bucket had cracked and came apart at the front bottom.
6 of 7 people found this instruction helpful.
  • Henry from ROWLETT, TX
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Watched a video on how to disassemble the old bucket and reassemble the new one. Piece of cake. Thank you for the part and how to video.

Henry
Was this helpful?
Thank you for voting!
The light was blown
9 of 16 people found this instruction helpful.
  • Frances from TUNNEL HILL, GA
  • Very Easy
  • Less than 15 mins
I turned the light bulb into the socket
Was this helpful?
Thank you for voting!
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
7 of 10 people found this instruction helpful.
  • Antonio from San Antonio, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
Was this helpful?
Thank you for voting!
Fan motor was making noise.
6 of 7 people found this instruction helpful.
  • Harry from Mountain Iron, MN
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First I removed all food in freezer.Then removed selves and hanger brackets.Then the back panel and light cover.Then I unplugged motor but before this I unplugged refrigerator from the wall.Removed motor from bracket after pulling of fan. Reversed the order to install motor and put back together
Was this helpful?
Thank you for voting!
Crisper drawer tilted to the right when pulled out
6 of 8 people found this instruction helpful.
  • William from Heathsville, VA
  • Really Easy
  • 30 - 60 mins
The repair consisted of lifting up the drawer cover and replacing it. Why the 60 minutes to do that? It took 58 minutes to clean the refrigerator.
Was this helpful?
Thank you for voting!
Noisy operation (from the inside)
5 of 5 people found this instruction helpful.
  • Frederick from APEX, NC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Unplug, then on the freezer side, remove the drawers, then remove the screws holding the sheet metal cover, remove the rails (for the drawer) that interfere with removing the sheet metal cover. pull the wires off the motor. There is a big plastic piece that holds a small plastic piece that holds the motor. Remove the plastic piece that h olds the motor/fan (you might be able to swap the motor by removing the little plastic piece that holds the motor, or you can remove the bigger piece and then remove the small piece that holds the motor). Pull the fan blade off (to reuse), swap the motor. NOTE - the new motor wire terminals may be on the opposite side of the motor vs. the old motor - that is not a problem - there is plenty of room for the wires. After the motor is installed put the fan blade back on, reinstall the removed plastic pieces in the back of the refrigerator. Now, I'd suggest a quick test. Make sure the new motor works and the fan blows before you button it up. Once you know it works, power it off, and put the sheet metal cover back on, reinstall the basket brackets, put the baskets back in place, close the door, and turn it back on.
Was this helpful?
Thank you for voting!
water leaked when the paddel was pushed
6 of 8 people found this instruction helpful.
  • Monica from EDMOND, OK
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .
Was this helpful?
Thank you for voting!
All Instructions for the 1065111
91 - 105 of 513