10646 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light Switch broke
48 of 78 people
found this instruction helpful.
-
James Richard from St. Cloud, MN
- Easy
- Less than 15 mins
-
Socket set
An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only
... Read more
swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.
Read less
Was this helpful?
Thank you for voting!
The ice maker stopped producing ice.
34 of 36 people
found this instruction helpful.
-
Robert E. from Payson, UT
- Easy
- 30 - 60 mins
-
Screw drivers
If you remove the bottom vent panel of the refrigerator there are two schematics for the refrigerator. One for the fridge and one for the icemaker. The icemaker has an emitter and a receiver that will tell the icemaker when it is ok to dump ice and add water. The receiver has an LED that blinks different codes. The codes give you an i
... Read more
dea where your problem is located. In my case it coded out to be the optics (emitter and receiver). Replacement of the parts involves the removal of three screws on each component and disconnecting a wire harness on each component. Install the new components by following the removal process in reverse. The total cost was $80.00. This was half the price Sears wanted for the parts and about the same price to have a Sears repairman just show up at the house.
Read less
Was this helpful?
Thank you for voting!
Auto Defrost Freezer keeps defrosting SIDE BY SIDE KITCHENAID
38 of 48 people
found this instruction helpful.
-
James from Ringoes, NJ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
DISCONNECT POWER. Removed all shelves/baskets.Popped upper panel off (just clips in) Removed 6 screws in lower back panel ( 3 each side) slid panel in place but down. You can then easily see the defrost thermostat/defrost termination switch. Cut the wire connectors (pink n brown wire) stripped back wire, attached new defrost thermostat.
... Read more
Thermostat clips on. New thermostat ohm's at 5.5, old one was "open". Slid cover back up meeting the upper cover grooves. Screwed lower panel in. Put shelves etc back in. Plugged in. Turns on, put a bottle of water in freezer. Checked a while later, frozen. has been frozen for a week.
-James
-James
Read less
Was this helpful?
Thank you for voting!
Noisy and the Fan wasn't blowing like it should
35 of 40 people
found this instruction helpful.
-
William from Centreville, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
I saved my Whirlpool Refrigerator (Model ET21GKXHN00) and learned a lesson. Don’t put off cleaning the refrigerant coils underneath the refrigerator. I replaced the refrigerator about 10 years ago and began to notice that the sound of this one running had changed slightly. I remembered that’s what happened to the first one just before
... Read more
it died. I removed the panel on the bottom front and saw that the refrigerant coils were covered with dust. It was really bad. I vacuumed them with the “radiator attachment” on the vacuum cleaner and plugged the refrigerator back in. It still didn’t sound right and I couldn’t feel the air blowing out like it should. So I rolled the refrigerator out and removed the back lower cover to see the compressor and the cooling fan. The fan was clogged with dust so I vacuumed that as well. But the fan wouldn’t spin freely by hand. The fan motor only had 3 screws holding it onto the plastic fan bezel and was easily removed by unsnapping the electrical connector on the motor. I removed the fan motor and tried to clean it with a few drops of WD40 on the shaft. But when I put it all back and plugged it in the fan just barely started turning. I unplugged the refrigerator and ordered the fan motor from PartSelect.Com (Item Number PS371043). The picture looked exactly like the motor that was in my refrigerator. I threw everything away in the refrigerator, cleaned it out and left it unplugged until the motor came. The motor arrived in a few days and it looked exactly like the one I had removed. It had the same electrical specifications stamped on the back and the electrical connector was the same and in the same location on the motor. I put the fan blade on the new motor and installed it exactly like the old one was. It only took 15 minutes or so and was very easy to install. When I plugged the refrigerator in the compressor started right away and so did the fan. It ran like a champ. In a few hours the refrigerator got cold and began to cycle on and off like normal and the fan blows like new. The sound is normal and the total running sound is quiet again like a new refrigerator. So for $84.67 I saved my $1300 refrigerator and learned not to neglect checking the build up of dust in the compressor fan section. I’m sure that’s what happens to most of the refrigerators people put out for trash pickup in front of their houses. The cause of the problem is when air flow is restricted across the refrigerant coils too much heat returns to the compressor and eventually causes the compressor to fail. I appreciate that we live in a time when you can order exactly what you need on the internet and make home repairs when you need to. Thanks Part Select for sending me the correct part. It’s nice to have milk and cold drinks again.
Read less
Was this helpful?
Thank you for voting!
Refrigerator Wasn't Cooling,Evaporater Coil Freezing Up
38 of 50 people
found this instruction helpful.
-
Robert from Doral, FL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I have a side by side so in order to access the bi-metal switch I first had to empty out the freezer. The switch is clipped on to the top of the evaporator coil. I had to remove 8 screws to remove the back panel of the freezer compartment. The bi-metal switch was right there in plain view. There are two colored wires that come out of
... Read more
the switch. I tried pulling them out of the socket they were plugged into but gave up for fear of breaking something. I ended up cutting the wires and splicing them together. I used the plastic twist caps. I made sure when I closed everything back up that the open end of the caps were pointing down so no water can accumulate in them. It has been 3 days now and so far so good
Read less
Was this helpful?
Thank you for voting!
Drawer was dropped and broken in one corner
36 of 46 people
found this instruction helpful.
-
Rolando from Edgewood, TX
- Really Easy
- Less than 15 mins
Removed the old one. Removed the handle attachment and placed it on the new drawer and slid it in place. Just that easy.
Was this helpful?
Thank you for voting!
Grid Assembly had a broken wire and would not separate the ice sheets into cubes
33 of 37 people
found this instruction helpful.
-
Brad from Bakersfield, CA
- Easy
- 15 - 30 mins
-
Nutdriver
I removed the 2 screws on each side of the grid and disconnected the electrical plugs attached to the grid. I slid the broken unit out. I then carefully slid the new unit in making sure not to pinch any of the electrical wires. I replaced the mounting screws, plugged the 3 connectors back into place and turned the ice maker back on. I ha
... Read more
d ice cubes within a couple of hours
Read less
Was this helpful?
Thank you for voting!
Had to replace a hose connector at the base of my refrig/frreezer
47 of 81 people
found this instruction helpful.
-
Leo from Salem, SC
- Really Easy
- Less than 15 mins
Perhaps a helpful hint:
When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.
LG
When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.
LG
Was this helpful?
Thank you for voting!
One finger of the spring steel peice that holds the ice maker and water dispenser levers out broke.
35 of 46 people
found this instruction helpful.
-
Ron from Newton, IA
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
I removed the screw holding the spring steel retainer/clip using a quarter inch ratchet wrench a swivel with a quarter inch socket and a short extention, then just installed the new one. This spring steal through the door ice maker / water despenser lever spring was an easy fix.
I found you by googling appliance repair parts, and fou ... Read more nd your site really easy to use. I couldn't believe how fast the part came and the very reasonable price. I put you on my web browser's favorites.
Thanks,
Ron
I found you by googling appliance repair parts, and fou ... Read more nd your site really easy to use. I couldn't believe how fast the part came and the very reasonable price. I put you on my web browser's favorites.
Thanks,
Ron
Read less
Was this helpful?
Thank you for voting!
Door chute broken
34 of 45 people
found this instruction helpful.
-
Dwight from Marietta, OK
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
First removed the outside cover plate which was some what scary not to break plastic cover. Had read about another discription of removal of cover to start from the bottom because the top is inserted in slots that would have broken if removed from the top. After cover plate removed it was simple to remove the broken parts and install th
... Read more
e new parts. The most difficult part to put back in was the spring and rod had to be inserted the same time.
Read less
Was this helpful?
Thank you for voting!
water mineral deposits on dispenser over-flow tray
37 of 55 people
found this instruction helpful.
-
Mark from Reno, NV
- Really Easy
- Less than 15 mins
Snap out - snap in.
Was this helpful?
Thank you for voting!
Refrigerator would ice up around the condenser and through out the air vents. Stopping all air flow in the refrigerator. If you defrosted the refrigerator it would work for about 24 hours then ice up again.
29 of 31 people
found this instruction helpful.
-
Richard from STATEN ISLAND, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Unplugged and empty refrigerator, completely defrosted refrigerator using a hair dryer to speed up the defrosting, put a lot of towels on the floor to soak up the water when the ice melts. Removed all refrigerator racks and drawers, then remove the white plastic and styrofoam condenser cover. You will then see the thermistor, cut the two
... Read more
small wires connecting the thermistor to the harness leave yourself as mush wire as possible. Splice in the new thermistor and put the refrigerator back together.
Read less
Was this helpful?
Thank you for voting!
ice would not drop
46 of 82 people
found this instruction helpful.
-
terry from panama city beach, FL
- Really Easy
- More than 2 hours
-
Nutdriver
removed the shaft that had worn end-replaced with new one- ok now
Was this helpful?
Thank you for voting!
Ice maker mold was cracked and leaking water into the bin which then froze all the cubes together.
28 of 30 people
found this instruction helpful.
-
George from Cottage Grove, MN
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I removed the ice maker assembly from the freezer compartment (four nuts/ nut driver) and unplugged the wire harness. I discovered the nature of the problem and I went on the Internet to look for replacement parts expecting I'd have to buy the entire ice maker. When I found PartSelect.com I looked through the pictures of the parts avai
... Read more
lable for my ice maker. I found the correct part quickly and easily. And having an acurate photo on the site, I was able to match all the key features of the mold I had with the one on the screen. I ordered the part, and installed it the day it arrived with just a Phillips screwdriver and a nut driver. It functions perfectly.
Read less
Was this helpful?
Thank you for voting!
Ice maker would only deliver crushed ice not cube's
36 of 54 people
found this instruction helpful.
-
MICHAEL from NORTH PORT, FL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Switched Electric breaker to off. Removed all food and ice cube tray from freezer. Remove 4 screws on soleniod cover in rear of freezer. Removed two screws, two elec connectors from old soleniod and removed. Installed new soleniod. Reinstalled elec connectors and screws, ice cube tray and food. Turned breaker on . Ice maker worked properl
... Read more
y.
Read less
Was this helpful?
Thank you for voting!