106445 Kenmore Refrigerator - Instructions

All Instructions for the 106445
121 - 135 of 782

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
My drawer had been broken and I needed a new one.
8 of 9 people found this instruction helpful.
  • Jennifer from Birmingham, AL
  • Really Easy
  • Less than 15 mins
When I took the pan out of the box, it was not the exact same as the one I had. But it fit perfect. The only hard part was the fact that it looked so good I had to clean the entire fridge side. (Smile)
Was this helpful?
Thank you for voting!
The Freezer defrosted and everything on the top and the bottom spoiled
10 of 16 people found this instruction helpful.
  • Jorge from Miami, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver
i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burn ed. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.
Was this helpful?
Thank you for voting!
Chrisper pan support cracked due to overfilling
9 of 13 people found this instruction helpful.
  • David from Lenexa, KS
  • Easy
  • Less than 15 mins
removed old shelf support after taking out the glass and support. New part was a perfect fit that was a "shap: to put in.
Was this helpful?
Thank you for voting!
fan making bad bearing noise
8 of 11 people found this instruction helpful.
  • Bruce from Malvern, OH
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
r&r fan blade and motor. with the parts you supplied it was easy. the parts were perrrrfect. thank you very much. job well done. bruce
Was this helpful?
Thank you for voting!
light not working in fridge
7 of 8 people found this instruction helpful.
  • Michael from East Meadow, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!
Was this helpful?
Thank you for voting!
Freezer wouldn't defrost/low temps in refrigerator
8 of 12 people found this instruction helpful.
  • Troy from Kansas, OK
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Found the housing for the thermostat; took housing apart pulled out thermostat and took off the hose put the hose on the new thermostat installed new thermostat and replaced housing.
Was this helpful?
Thank you for voting!
freezer gets too cold then gets to regular tempetured
6 of 6 people found this instruction helpful.
  • roberto from san Antonio, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
disconect the power removed the screws with the phillips screwdriver removed the front cover and then removed the rest of the screws. removed the three covers and then removed the thermostat. replaced in reverse order.
Was this helpful?
Thank you for voting!
Broke Glass on shelf
8 of 12 people found this instruction helpful.
  • Sandra from Valencia, CA
  • Really Easy
  • Less than 15 mins
The drawings of my side by side refrigerator on your web site made selecting the correct part very easy. The part arrived very quickly and I placed the shelf in the refrigerator and added the snack drawer. Thank you!
Was this helpful?
Thank you for voting!
Door bin was broken
6 of 6 people found this instruction helpful.
  • Andrea from Cornelius, NC
  • Really Easy
  • Less than 15 mins
took old bin out replaced with new , two minute job
Parts select is an easy co. to do business with THANKS Andrea
Was this helpful?
Thank you for voting!
broken drawer
8 of 12 people found this instruction helpful.
  • Thomas from North Port, FL
  • Really Easy
  • Less than 15 mins
replaced
Was this helpful?
Thank you for voting!
Crack in vegetable drawer
6 of 6 people found this instruction helpful.
  • Paul from NAYLOR, MO
  • Very Easy
  • Less than 15 mins
Emptied draw of contents pulled draw out and inserted new drawer....easy pea-zee
Was this helpful?
Thank you for voting!
Shelf cracked, and crisper was accidentally broken by me....
6 of 6 people found this instruction helpful.
  • Patricia from DRACUT, MA
  • Very Easy
  • Less than 15 mins
Awesome
Was this helpful?
Thank you for voting!
Fan motor was making noise.
6 of 7 people found this instruction helpful.
  • Harry from Mountain Iron, MN
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First I removed all food in freezer.Then removed selves and hanger brackets.Then the back panel and light cover.Then I unplugged motor but before this I unplugged refrigerator from the wall.Removed motor from bracket after pulling of fan. Reversed the order to install motor and put back together
Was this helpful?
Thank you for voting!
Black Cam was bren on lower door hinge
6 of 7 people found this instruction helpful.
  • Kyle from Wimauma, FL
  • Very Easy
  • 15 - 30 mins
  • Socket set
This was a very simple job. Remove the top Hinge bracket, a total of 4 screws, lifted the door off the bottom hinge, removed the bottom hinge set up, 2 screws, replaced it, and attached the new bottom black door cam, lifted the door back onto the bottom hinge and aligned the top hinge, and reinserted the screws, and Ta Da, The door works like a new refrigerator door. 15 to 30 min tops. I did not even have to take the refrigerator items out of there door holder.
Was this helpful?
Thank you for voting!
I had a broken door bin
6 of 7 people found this instruction helpful.
  • Lorraine from Brush Prairie, WA
  • Really Easy
  • Less than 15 mins
Nothing to do, part came, fully assembled, it just went right into the door. Yea!!!
Was this helpful?
Thank you for voting!
All Instructions for the 106445
121 - 135 of 782