1064211173 Kenmore Ice Maker - Instructions

Removed end cover from ice maker assembly. Motor driven wheel had broken from its plastic shaft. Disconnect power source. Using philips screwdriver, remove three screws from corners of motor mold and remove mold. Per instruction on end cover, rotated strips arm ice ejection tines until they pointed in the two-o'clock position. Dry fit (without screws)new motor mold assembly to ensure that the shaft with flat engaged the socket with flat and that the new part assembly seated flat on icemaker housing re-install 3-screws. Re-connect power source. After 2 hrs. , Confirm that ice cubes are being produced.

my husband just took the motor off the existing maker and decided the front part of the unit was bad, I ordered it and it came in about 3 days he put the new front on it and screwed the unit back in the freezer, was about 4 screws I think. Didnt take too long but I would bet the next time it would be easier. Thank you

Followed the instructional video. It was not exactly like the unit I had but I followed as much as possible. I switched out the motor and within 3 hours had ice.

Removed ice maker from freezer area. Motor in ice maker was not rotating ice dump bar. Replaced control and motor assembly. Problem solved.

Repair was easy and the video on PartSelect was spot on. Basically you take the unit out of the freezer, undo three screws, take out the old motor assembly and put in the new one, replace the screws, and put back in the freezer. Simple.

This is the 4th motor on this ice maker. Sears replaced the original motor at a cost of >$300 and this is the 2nd motor I have replaced at a cost <$70.
Repair is quite easy since this was the As described on your site, simply remove the door flap, remove the covering for the wiring, remove 3 hex nuts under the floor of the unit and the entire ice maker slides out. After disconneting the wires, you simply slide the cover from the motor, remove 3 philips screws and slide the old motor out.
Align the new motor, slide in, replace 3 philips and reverse the process to place the ice maker and hex nuts.
Was "back in ice" within an hour or so.
Thanks for the instructions and video and for making the parts affordable for do-it-yourselfers!

replaced Icemaker Control and Motor Assembly

I actually went on your website and used the do it yourself repair video as a step by step guide to complete the repair. It was as easy in real life as it was presented on the video. I will use this website to buy and repair future issues I may face with my appiances.

I removed three screws holding unit to the freezer wall. Disconnected power cable. Removed three screws in motor assembly. Detached the old motor assembly. Attached new assembly with same three screws. Re-mounted unit to the freezer wall and re-connected power. One hour later, I had ice again.

a ice cube got hung up burnt motor up.trimed plastic away from water tray.restalled new unit.works great now.thanks for your help.phillip

My son's ice maker quit over 5 yrs ago. Repairman told him he would need whole unit.
I keep trying to fine the "whole unit". I finally wnet on to the part list and decided
it was probably the Modue assembly. I odereded it and guess what!!!! That was it....a $66 part!
It is working fine now!!

Removed icemaker found ice mold protective layer coming off. Replaced ice mold and working great. Online graphic very detailed and easy to determine part needed. Easy and great delivery. Highly recommended for future repairs.

After determining that the gear on the motor assembly had broken off, I ordered from this website. First time using Partselect, and will now always check and hopefully order here first. Repair was very easy. Pulled the old assembly off by taking out three screws, removed the broken assembly, put the new one on, replaced the three screws, and installed the icemaker back into the freezer. Took a about 30 min total. Came back in about an hour and had ice!

After reading solutions to my problem on your website I ordered the part which fixes 50% of the problems. When I got back after Christmas the part had arrived. I removed the Icemaker and replaced the part. It took aprox. 20 minutes for the job. It was easy. Now we have ice cubes again.

easy as pie everthing good thanks