10641172713 Kenmore Refrigerator - Instructions

Steps to replace Whirlpool evaporator fan motor
1. Watch numerous DIY Youtube videos
2. Move frozen food to refrigerator section, close refrigerator door
3. Cut power to refrigerator
4. Remove all shelves and bins in freezer section
5. Back panel has two parts, a top and a bottom section
6. Unclip small shroud covering screw bolt in upper left corner holding top panel. Remove screw bolt
7. Gently pull and work top panel out
8. Remove screw bolts from all four corners in lower panel and remove bottom panel
9. Verify power has been turned off
10. Unclip grounding wire
11. Unclip evaporator fan motor from power
12. Remove whole cradle holding evaporator fan motor. Note orientation of cradle. Fan blade is slightly angled toward the back of freezer. In other models, the cradle may not be removeable.
13. Remove plastic fan with firm pull
14. Unclip bottom brace to remove evaporator fan motor
15. Replace old grommets in bottom brace and on top of evaporator fan motor with the new grommets
16. Install new evaporator in cradle and clip-in the bottom brace
17. Install new fan blade on motor
18. Place cradle with new evaporator fan motor back in freezer
19. Reclip power and ground wire
20. Turn on power and test if working correctly
21. Turn off power
22. Complete steps from 8 to 2 in reverse

Easy repair, third time in four months, same part. I don't recommend Whirlpool refer's. Stick to the washer and dryers.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

No repair needed. Just inserted the storage bin onto the hooks provided on the inside of the door.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Access back of unit, lower left corner. Remove wire capacitor retention clip. Unplug cold capacitor, plug in replacement, reinstall wire retention clip, test.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

watched video on your website and followed directions

Looked up on you tube to verify and see "secrets" to installation.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

The repair was super easy. It took all of 10 seconds. From ordering the part to repair, I would use part select 100%! Excellent company with excellent parts. Thank you!

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I just followed the excellent Video for both parts. The door gasket is tedious but doable, just take a deep breath and press on. Putty knife is handy to push edge of gasket under the plastic lip. The closer devices take 3 minutes - simple R&R. Check the videos - they're pretty clear and detailed.

Very simple fix, remove 3 screws, two connectors to the old switch