10641159210 Kenmore Refrigerator - Instructions

using a flat blade tool removed old main light board and installed new light board, light now works fine.

Simple fix. I watched the video it was great.

Very simply change old part just by hand

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

Well the actual repair took just as long to find Partselect online, plug my model# in, find the parts and wait until they came by mail! The bad part was the cleaning of the refridgerator which was in a home that my boyfriend & I bought which had mice running through it! They chewed the crisper drawer and the other drawer was cracked in half. I would definitely come back to your site for any appliance parts in the future! I may be in need of cook top parts, real soon!

I removed the three small bolts (under cosmetic cap) located on the right top hand side of the refrigerator and pulled off the door. Replaced the top and bottom cams, put back on the door, screws and cap. Door works like new and the Wife loves it.

On a side note, don't be confused when ordering the top and bottom cam as they are both on the bottom of the door.

First I removed the three screws on the top hing of the refrigerator door so that we could lift it off the bottom hing. Socket wrench bits for my drill made that fast and simple. I lifted the door off the bottom hing to find the door closing plastic cam to be broken in several pieces. The hardest part was getting the cylinder shape piece that had broken off the cam out from inside the door. This way we would be able to insert the new piece. Needle nose pliers are the right tool for that job since the hole is small and the plastic just frays under force from regular pliers. It took some force and patience to get that out, but once all the broken pieces were removed, reassembly was quick and easy

Simply slid the crisper pan into the guides.

I searched Google using the part number from Whirlpool and found PartSelect immediately. They were the best price and had the item in stock. I received it w/i 2 days! I like that they use a gridded background of 1" squares in the picture of the item to demonstrate its dimensions/size.

It slid right in.

Maintenance completed. Some difficulty.

DISCLAIMER: Technically, you should start by unplugging the frig and turning off the water supply. Though there is nothing on the my frig door that is either electrical or water related, the frig does keep trying to cooling an open area. For the short while I was doing the work, I just didn't want to bother with those precautions. Had I expected the work to take longer or been working on the FREEZER door I would have most certainly have done it "correctly." But I didn't do the freezer door so, first, remove everything from the refrigerator door storage shelves and the shelves themselves. Then lift off the cap that covers the hinge mounting plate on top of the frig. Remove the screws that holds the mounting plate in place. I used a cordless drill/driver with a 1/4" socket on the end but this could be done with a nut driver or socket wrench as well. Of course, take care not to let the door fall when removing the last screw. Then, lift the door off the bottom post that his holding it in place. The door is not too heavy and one person should not have a problem doing this but if you think it might be too heavy get someone to help with this. On the frig door there are no other connectors to be concerned with. NOTE: This procedure is similar for the freezer door but there are electrical and water line connections that need to be addressed before removing the door. Once the door is off the post, lay it down on a flat work service (I used the kitchen table with some towels spread underneath to prevent scratching either the table or the frig door.) There are two pieces that ought to be replaced. One cam on the door and one at the bottom post. Both are attached with a small screw that is removed easily with your nut driver/socket/drill driver. The bottom cam came offer fairly simply but sliding a thin, flat blade screw driver under it and prying it up and off. Replace this bottom cam with a new one and screw it back down. The door cam was, for me, the more difficult item. Removing the screw was easy enough but years of wear and brittleness led it to break off as I was trying to pry it out. I was able to use a small flat blade screwdriver to cave the old plastic post in all around the insert hole until I could get a good hold and pull it out with needle nose pliers. I was tempted to try to drill the old post out but there is a hex shape to the insert hole I was afraid of ruining. Once I got the old cam out, it was a simple matter to re-insert the new cam. Since both the door and lower cams are held on by screws there is only one way they can go back on. Once the cams are back in place, lift the door back onto the post and reattach the mounting plate to the top of the frig. Take some care that the door is level and parallel to the freezer door before completely tightening the mounting screws and replacing the cap that covers the plate. If you did shut off water and unplug the frig you should turn it back on and plug it back in. And do I really need to tell you to put the shelves and stuff back? :) The door should close on its own when close enough to the frig frame that the cam notches slide into place. If it hadn't been for the door cam being so brittle, this repair would have quite simple. Even at that, digging the old post out really wasn't hard but it did take some unexpected effort. If your refrigerator door is not closing properly, this is something anyone with basic skills can do.

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

Remove all contents from refrigerator door. Removed top hinge (3 machine screws). Remove door & place on table. Remove closing cam from bottom of door & install the replacement-reassemble. Very easy repair for a very annoying problem. Lots of descriptions on You Tube as well.

Saw online info video explaining the possible cause and how to fix it. Ordered upper closing cam. Removed top hinge cover and hinge, removed door set it on a table. Removed old cam installed new cam tightened the retaining bolt put the door back on aligned it with freezer door and bolted it down snug. No more noise and it took less the half and hour.