1064113 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replace Bad Switch
0 of 1 people
found this instruction helpful.
-
carlos from haverstraw, NY
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place
Was this helpful?
Thank you for voting!
old switch left freezer bulb always-on
0 of 1 people
found this instruction helpful.
-
JONATHAN from ELKINS PARK, PA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.
Was this helpful?
Thank you for voting!
non-functioning refrigerator lite switch
0 of 2 people
found this instruction helpful.
-
Ronald from Billings, MT
- Really Easy
- Less than 15 mins
-
Pliers, Wrench set
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sin ... Read more cerely, Ron Marshall, Billings, MT
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sin ... Read more cerely, Ron Marshall, Billings, MT
Read less
Was this helpful?
Thank you for voting!
light switch would not work
0 of 2 people
found this instruction helpful.
-
Joseph from Destin, FL
- Really Easy
- Less than 15 mins
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
Was this helpful?
Thank you for voting!
The light went out
0 of 2 people
found this instruction helpful.
-
Janet from Flagstaff, AZ
- Easy
- Less than 15 mins
-
Screw drivers
I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.
Was this helpful?
Thank you for voting!
black scratchers from wheel chair
3 of 12 people
found this instruction helpful.
-
Linda from GLEN CARBON, IL
- Very Easy
- 30 - 60 mins
shook bottle and painted waited a day and repeated
Other Parts Used:
Was this helpful?
Thank you for voting!
The ice dispenser handle wasn't working properly. Sometime when dispenser handle was pressed it didn't dispense ice on the first try.
2 of 10 people
found this instruction helpful.
-
Richard from CONYERS, GA
- Really Easy
- 1- 2 hours
-
Screw drivers
I installed a Ice Door Kit. It works Great Now!
Was this helpful?
Thank you for voting!
Switch was not working after a repairman had fixed something else
0 of 4 people
found this instruction helpful.
-
Jackie from Nova, OH
- Really Easy
- Less than 15 mins
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a
... Read more
single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Read less
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people
found this instruction helpful.
-
Howard from Boynton Beach, FL
- Easy
- 30 - 60 mins
-
Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol
... Read more
oring refer handles. Thank you
Read less
Was this helpful?
Thank you for voting!
Both light bulbs had been replaced, but lights did not turn on.
-
Richard from Arlington, MA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this helpful?
Thank you for voting!
Switch didn't work
-
Don from Laramie, WY
- Easy
- 15 - 30 mins
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this helpful?
Thank you for voting!
Broken rear support wheel
-
Adam from Freeland, MI
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed app
... Read more
rox 3/4" under edge of refrigerator.
Read less
Was this helpful?
Thank you for voting!
Heard a five second buzzing sound repeated 4 or 5 times per cycle coming from rear lower left compressor side.
-
Burton from Pecatonica, IL
- Easy
- 15 - 30 mins
-
Nutdriver
Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.
Was this helpful?
Thank you for voting!
Light switch in the refrigerator was faulty from the first day we installed the fridge.
-
Mary from Wasilla, AK
- Easy
- Less than 15 mins
-
Screw drivers
I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world whe
... Read more
re my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!
Read less
Was this helpful?
Thank you for voting!
No light in frig
-
Irene from Whitehall, MT
- Really Easy
- Less than 15 mins
We tried repairing with a new switch which was very easy to install but it didn't fix the problem.
Was this helpful?
Thank you for voting!