10632853010 Kenmore Refrigerator - Instructions

Removed/replaced ice maker and valve per enclosed instructions. If you can service your own lawn mower this R&R should be easy for you.

unplug, turn water off, remove ice maker & unplug,remove back panel remove old fan unit & unplug remove fan remove fan blades just pull off install new fan, put fan blades on new fan & install on bracket & re install plug in re install back panel. plug in ice maker re install ice maker . turn water back on plug refrigerator back in ( quite easy )

Discard the broken crisper pan and replace with the new one

I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

I cut the plugs off and bought male and female wire conectors and crimped them on the wires and pluged them together.

The fridge was prepped for an ice maker but was never installed. After much aggravation of people not filling the ice trays I gave up and installed the ice maker. This is probably the hottest summer on record, and we were going thru a lot of ice. Lost a little real estate in the freezer by the ice maker but it was well worth it. Now I know I have fresh ice for cocktails in the evening!Install was fast and easy. A little longer than usual because I had to run the water line as well.

We had a refrigerator that had no ice maker at all, but it had the wiring behind the freezer panel and the wiring for the solenoid valve at the bottom of the refrigerator. The installation went easy for me, but I do not think the average homeowner could handle it. There are always little variations from model to model so some of the diagrams were not quite the same as my unit. But all the necessary parts and hardware were there and the install went fine. its crabnking out perfect ice like crazy.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

Rather than pay a repairman an assessment fee, then the cost of the repair to the existing icemaker, I decided to replace the icemaker for a lot less. The Add On Icemaker kit came with installation instructions. The kit included the ice maker, as well as the hose and water feed control on the back. Originally, I was nervous about attempting to replace the icemaker. I watched a video on YouTube about replacing an icemaker and saw how easy it could be. Following the enclosed directions, and Wow!, it was extremely easy to remove and add the new icemaker. Don't pay to have someone else do it! This is a no-brainer.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

Discovered that the fan in the freezer was not working properly. Removed the ice maker, paneling, wire harness and inserted new motor. Worked immediately and began circulating the cold air into the refrigerator.

Switch off power at mains outlet. Pull off the front trim panel on the control box at top of the refrigerator compartment (it is just clipped into place). Behind are two screws which you remove. Remove the bulb and also two screws underneath and towards back of the control box. You can then pull down the control box. The defrost timer board is now visible and can easily be switched out (it comes with instructions how to do this). This job too no more than 20 minutes and saved me buying a new refrigerator at $1000.

unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.

My husband tackled the job....but before this repair he had to replace ours at home so he had some experience at it....although...on this fridge he had to hook up the water line and all...but basically was not too hard...and the ordering of the part and delivery was excellent...