All Installation Instructions for Admiral Range 1058AF-CW

Dirty drip bowls

Just remove old bowls from range top and put new ones. That is all ... just super simple! :)

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Paul from Carnegie, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Drip bowls were all rusted.

Removed old rusted drip bowls and put in the new ones. Very easy to do and needed no tools. It made my 25 plus Jenn Air look new again!

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Robin from Seneca, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

old drip bowl was worn out

new drip bowl fit perfectly and was a snap to install.

Parts Used:

Chrome Drip Bowl - 8 inch

Richard from Germantown, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Oven light Switch

Compressed the springs and removed the damaged switch, then changed the wiring over to the new switch and press into place, worked fine.

Parts Used:

SWTCH-LITE

William from APACHE JUNCTION, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Burner element stopped working

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.

Parts Used:

Surface Burner Receptacle Kit

Robert from Lodi, CA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

Was this instruction helpful to you?

Burner did not heat, but element is ok.

The Burner Control Switch - 250V Part Number: PS2089409 that this site recommended was the right part for this older range. Had to remove screws to pull out the front panel with knobs, but it only pulls out a couple inches due to wires so it is tight to remove old switch. The five tabs are not in same spot so go by the labels and the wire lugs fit just fine, and the knob snapped right on and works great. Thank You!

Parts Used:

Range Surface Element Control Switch

Philip from Hull, MA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Light bulb failure

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Parts Used:

Light Bulb - 40W

Grant from Alexandria, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner stayed on "high", could not adjust heat

I UNPLUGGED STOVE, removed panel covering the controls, removed the knob on front and the two screws there that hold the control in, inserted new control and replaced the two screws on the front that hold it onto the stove, used needle nosed pliers to unplug one connection at a time from the old control and onto the new control in the back. When I had all connections plugged onto the new control I re-installed the panel cover with a screwdriver, plugged the stove back in, and the burner is now working good as new!

Parts Used:

Range Surface Element Control Switch

Deborah from Hodgen, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Right-side oven door spring broken

Range is a 1967 model Maytag. First I removed drawer under oven, unplugged the range and pulled it out from the wall. Removed oven door by positioning it in the partly-open detent position, then pulled up to remove the door. Next I removed 7 screws per side panel: 3 in front and 3 in back, and one on top under cooktop, which retains the cooktop hold-down clip. With side panels removed, I noted the oven door spring position on the intact left side, then replaced the right-side spring first using the same spring adjustment positions. As I replaced the spring, I applied lithium grease to the spring hook pivot points as well as the spring coils where they rub against the interior wall. I repeated the process on the left side. I reassembled the side panels, oiled the door hinges and reinstalled the oven door. Reinstalled range and bottom drawer. The oven door operates like new, and the new springs are totally quiet — good for another 47 years!

Parts Used: