1039887621 Kenmore Range - Instructions

All Instructions for the 1039887621
31 - 45 of 49

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The control knob stem broke off when I moved the stove.
3 of 10 people found this instruction helpful.
  • Jonathan from Harvard, MA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters do n't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people found this instruction helpful.
  • Roscoe G from ROCHESTER, NY
  • Very Easy
  • Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
instructions could be better
0 of 6 people found this instruction helpful.
  • WILLARD from GLOVERSVILLE, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank
Was this helpful?
Thank you for voting!
rht. front element would not heat properly
  • Rod from Huron, OH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this helpful?
Thank you for voting!
drawer coming out of the track and falling to the floor.
  • Steven from Waukesha, WI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
pulled drawer out and installed drawer guide
Was this helpful?
Thank you for voting!
element heat wouldn vary
  • Leonard from Winter, WI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this helpful?
Thank you for voting!
Plastic Insert for knob to long, had to use my bench grinder to cut it down
  • Floyd from Warren, OR
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this helpful?
Thank you for voting!
burnt out element
  • chuck from battle creek, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
turn off power, remove 2 screws, lift off of hanger , slide out far enough to unplug wires. remove brackets from old element, I did have to use a screw driver to open up bracket to slide over new element(new element a little larger diameter coil) reverse removal. DONE !! Thank You Part Select !
Was this helpful?
Thank you for voting!
Light in oven had blown and needed to be replaced
  • Sandra from Marietta, GA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I did not do it, I instead had my neighbor put the gasket around the light lens cover and replace it. He considers himself a handy man, so it was easy for him.
Was this helpful?
Thank you for voting!
Clips needed to re attach heating element
  • Dennis from Orlando, FL
  • Really Easy
  • Less than 15 mins
  • Pliers
Pulled out old with pliers. Twisted new clips in per instructions.
Was this helpful?
Thank you for voting!
broiler element burned out
  • daniel from fort mill, SC
  • Really Easy
  • Less than 15 mins
  • Pliers
shut off power to range, removed old element, looked up part on line, shopped for best price, Part select was $30 less than sears replacement part, ordered part, part arrived in 4 days, installed new part and I was broling again.
Was this helpful?
Thank you for voting!
Drawer guide
  • Lee from Grass Valley, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Used Phillips screw driver, installed guide, applied lubricant.
Was this helpful?
Thank you for voting!
Broiler Element Burned Out
  • Arthur from Midlothian, VA
  • Easy
  • Less than 15 mins
  • Socket set, Wrench (Adjustable)
1)Undid two hex nuts holding broiler element in place. 2)Slipped fasteners off pegs connecting element to oven. 3)Simply reversed the process, when installing new element.
Was this helpful?
Thank you for voting!
Knob had broken off
  • DeeAnn from Clinton, MO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
My husband was able to easily remove and replace the switch and know with-in 15 minutes.
Was this helpful?
Thank you for voting!
Burned Out Broil Element
  • William from Eufaula, AL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
The repair went ok. I did have to take the back off the stove in order to get to the wire connectors. Needed an extra person to move the stove out of it's location. Just had to be careful.
Was this helpful?
Thank you for voting!
All Instructions for the 1039887621
31 - 45 of 49