10392 Kenmore Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken bake element
0 of 1 people
found this instruction helpful.
-
Harvard Folding Box Co from Lynn, MA
- Really Easy
- Less than 15 mins
-
Nutdriver
Shut off electrical supply to stove.Remove 2 screws.
Slide element out enough to remove connectors from element.
Position new element.Slide connectors onto new element.
Slide element back into position.Replace 2 screws.Turn on electrical supply.
Slide element out enough to remove connectors from element.
Position new element.Slide connectors onto new element.
Slide element back into position.Replace 2 screws.Turn on electrical supply.
Was this helpful?
Thank you for voting!
Heating element worn-out
0 of 1 people
found this instruction helpful.
-
Mary from Bivalve, MD
- Really Easy
- Less than 15 mins
-
Pliers
Turned off the breaker to the stove, removed oven racks, used small pair of plyers to remove bolts (2) holding defective element in place. Pulled (2) wires that had a snap connection apart. Old element was not removed. Connected (2) snap wires, pushed them back into the oven wall, used plyers to re-connect the element to oven. Install
... Read more
ation DONE!
Turned on breaker and then the oven; we are now baking again.
Turned on breaker and then the oven; we are now baking again.
Read less
Was this helpful?
Thank you for voting!
Heating element broke and not working
0 of 1 people
found this instruction helpful.
-
brad from flatwoods, KY
- Really Easy
- Less than 15 mins
-
Socket set
Watched youtube....
Was this helpful?
Thank you for voting!
old bake element broke
0 of 1 people
found this instruction helpful.
-
Andrew from Cary, MS
- Easy
- Less than 15 mins
-
Nutdriver, Pliers
This is how I did it--but I would strongly recommend you do step 4 first, and skip step 3! Remember, because 240V circuits have 2 "hot" wires, they may be "hot" (120V to ground) even when switched off!
1. Removed the mounting screws with a nut driver.
2. Pulled out the old element. BARE lug connectors on loose wires came ... Read more out with it.
3. Watched an impressive show of sparks.
4. TURNED OFF THE CIRCUIT BREAKER.
5. Separated the connectors. Had to use pliers on the one I "fried".
6. Connected new element (connectors pushed together easily.
7. Reattached with screws
8. Turned breaker back on.
1. Removed the mounting screws with a nut driver.
2. Pulled out the old element. BARE lug connectors on loose wires came ... Read more out with it.
3. Watched an impressive show of sparks.
4. TURNED OFF THE CIRCUIT BREAKER.
5. Separated the connectors. Had to use pliers on the one I "fried".
6. Connected new element (connectors pushed together easily.
7. Reattached with screws
8. Turned breaker back on.
Read less
Was this helpful?
Thank you for voting!
Heating element broke and not working
0 of 1 people
found this instruction helpful.
-
brad from flatwoods, KY
- Really Easy
- Less than 15 mins
-
Nutdriver
Watched youtube. Easy and fast!
Was this helpful?
Thank you for voting!
metal "Y",shape metal long arm attached to burner came loose.holding the coil to burner
1 of 4 people
found this instruction helpful.
-
Audret K, from San Diego, CA
- Really Easy
- Less than 15 mins
just plugged in the two prings into burner into outlet. Very simple and quick.
Was this helpful?
Thank you for voting!
bake element in oven burned out
0 of 1 people
found this instruction helpful.
-
Amy from Etna, CA
- Easy
- Less than 15 mins
-
Wrench set
Using a wrench, removed old element and simply installed new one - took less than 10 minutes and the oven was working again! Best part was how quickly the item reached us - ordered it on a Wednesday afternoon and had it by Friday afternoon, with no expedited shipping - Great Service!
Was this helpful?
Thank you for voting!
Bake element burns out heating up easter dinner
0 of 1 people
found this instruction helpful.
-
joseph from mastic, NY
- Really Easy
- Less than 15 mins
Uplugged the oven and undid the back contact cover, removed the nuts inside the oven and slid out the element. Pushed the new element into place and secured it. Attached the contacts and replaced the cover. Plugged it in and got cookin'.
Was this helpful?
Thank you for voting!
Bake element had broke and caught fire
0 of 1 people
found this instruction helpful.
-
Joey from barto, PA
- Really Easy
- Less than 15 mins
-
Wrench (Adjustable)
It was real easy all I had to do was turn the breaker off,Undo two srews and disconnect the two wires. Then repeated the process to install
Was this helpful?
Thank you for voting!
bake element burned out, lower unit
0 of 1 people
found this instruction helpful.
-
Murray from Franklin Square, NY
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
removed nuts from inside, removed rear panel, pulled old
part out, slipped new part in.
DONE
SHIPPING AHEAD OF TIME, YOUR COMPANY SAVED ME THE PURCHASE
OF A NEW STOVE. THANK YOU FOR FAST & GOOD SERVICE.
NO ONE HAD THE PART BUT YOU FOLKS.
part out, slipped new part in.
DONE
SHIPPING AHEAD OF TIME, YOUR COMPANY SAVED ME THE PURCHASE
OF A NEW STOVE. THANK YOU FOR FAST & GOOD SERVICE.
NO ONE HAD THE PART BUT YOU FOLKS.
Was this helpful?
Thank you for voting!
oven was not heating properly
0 of 1 people
found this instruction helpful.
-
Susan from SAlisbury, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
took out the old element after cutting the circuit breaker, put in the new one, it was that easy
Was this helpful?
Thank you for voting!
Oven wouldn't heat
0 of 1 people
found this instruction helpful.
-
Craig from Catasauqua, PA
- Really Easy
- Less than 15 mins
-
Nutdriver
Turned power off. Removed two screws holding the element. Pulled element out 3 inches, disconnected the two wires, pulled out old element, connected wires of new element, replaced screws. Turned power back on. Eureka!! the oven heats again. :-)
Was this helpful?
Thank you for voting!
the old oven element burned in two.
0 of 1 people
found this instruction helpful.
-
Kenneth from Newport, OR
- Really Easy
- Less than 15 mins
-
Nutdriver
After removing the screws holding the element in I disconnected the wires and attached alligator clips to the wires to keep them from pulling back inside the holes. I would have had to pull the stove out and removed some covers if they disappeared through the holes. After getting the part number off of the old element, I ordered a new e
... Read more
lement from Partselect.com and received the new one in less the a week. Reinstalling the new element took about 5 minutes.
Read less
Was this helpful?
Thank you for voting!
Bottom element cracked/split - open circuit
0 of 1 people
found this instruction helpful.
-
Al from Charlotte, NC
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed oven shelves (30 seconds). Removed 2 screws holding broken element to oven (2 minutes). Pulled broken element assembly out & removed 2 wires attached to element (1 minute). Connected wires to new element (just push them into place) and mounted new element with the 2 screws (1 1/2 minutes). Turned on oven element to test & sinc
... Read more
e I was so tired from all of this 5-minute activity, I rested.
Al S.
Al S.
Read less
Was this helpful?
Thank you for voting!
Element broke
0 of 1 people
found this instruction helpful.
-
Kim from Vancouver, WA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
First I switched the fuse to the oven had no power and then I removed the old element and wiped down the inside with a damp towel.
I then attached the new element and then used the screws to attach the element firmly into place.
I then restored power by switching the fuse back and then burned the element to remove and chemicals ... Read more and then done
I then attached the new element and then used the screws to attach the element firmly into place.
I then restored power by switching the fuse back and then burned the element to remove and chemicals ... Read more and then done
Read less
Was this helpful?
Thank you for voting!