10392 Kenmore Range - Instructions

All Instructions for the 10392
76 - 90 of 285

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
baking element arced and burned out
1 person found this instruction helpful.
  • Norman Levitz from Manchester Center, VT
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to swap out the parts and... success!
Don't forget to turn off the circuit breaker before starting repairs.
Was this helpful?
Thank you for voting!
The bake element caught on fire. I needed to replace the burner..
1 person found this instruction helpful.
  • Sandra from Muskegon, MI
  • Really Easy
  • Less than 15 mins
  • Socket set
All I had to do was just unscrew the bolts,pull out the old one, and put the new one on its metal clips and then rebolt.So easy and I know I would have had to pay much more then what I did for the part..This place is super.I ordered my part one day, and it was there the next...Sandy
Was this helpful?
Thank you for voting!
The bottom bake element was burned out.
1 person found this instruction helpful.
  • Richard from State College, PA
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
1. Turned off electrical breaker for range.
2. Removed the two hex head screws that hold element in place.
3. Pulled element out and unplugged the two electrical connectors.
4. Attached connectors to new element and attemped to push element back into the opening. It would not go in all the way.
5. Apparently some of t he insulation had fallen down and was blocking the area where the element slides in.
6. I used a long thin screwdriver inserted into the two holes to push the insulation aside.
7. The element was then able to go in all the way.
8. Replaced two hex head screws.
9. Turned on range breaker.
10. Turned on oven. Works fine.
Was this helpful?
Thank you for voting!
element broke, oven wouldn't heat - still doesn't
1 person found this instruction helpful.
  • TESS from BOSWELL, PA
  • Easy
  • Less than 15 mins
  • Socket set
first husband removed the bolts unplugged old element wires -plugged in new element wires and but in bolts - unfortunately the oven still doesn't work not sure if element is bad or wiring, need professional help
Was this helpful?
Thank you for voting!
Bake Element went out..flamed out pretty big light show when it happened
1 person found this instruction helpful.
  • Don from Martin, TN
  • Easy
  • Less than 15 mins
  • Socket set
The job went over without a hitch, only probably didn't get the correct part first go around, but after getting the right part everything went very easy..Just a couple of screws where the elment goes in and 2 wires to plug back into the new element, after that everything was good to go!!
Was this helpful?
Thank you for voting!
Bake Element on Oven Arced and Split
1 person found this instruction helpful.
  • Lisa from The Woodlands, TX
  • Easy
  • Less than 15 mins
  • Socket set
Instead of flipping circuit breaker, we pulled the oven away from the wall and unplugged it. Used socket wrench to loosen screws of bracket holding old element onto the back oven wall, then gently pulled element until connecting wires appeared. Removed the 'clips' attached to the old element prongs and discarded old element. Reattached the 'clips' to new element prongs, then gently pushed prongs into back into oven wall until the bracket was flush with the wall. Used socket wrench to screw and tighten the bracket into place. Plugged in the oven and tested the new element to make sure it worked. The whole process took only a few minutes.....it took longer to clean the oven before installing the new element.
Was this helpful?
Thank you for voting!
The element on our three year old stove stopped working...this was the bottom bake element.
2 of 4 people found this instruction helpful.
  • shawn from port richey, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was surprisingly simple. All I had to do was shut the breaker off to the stove(safety first). Next open the oven door and use a flashlight just to help you see,and unscrew the two screws holding the element in place on the back stove wall. Next slide the stove away from the was to give yourself enough room to access the back of it(you may need to unplug it to get it out far enough. My model had a cover over the back that took six easy to remove screws. Once the back cover was off I could easily see where the element was plugged into, so i removed the wires from the end of the element(just female terminals slipped over the end) i then went back to the front of the stove and pulled to element out.

To install the new one...just guide the two ends throgh the back of the stove...install the two screws to hold it in place...go to back of stove..plug in wires(they were diff sizes so you couldnt mess it up) and put the cover back on..plug in oven..slide it back..and try it out...its that simple
Was this helpful?
Thank you for voting!
Hanging broiler
2 of 5 people found this instruction helpful.
  • Doris from Aberdeen, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers
Quick and easy, thanks!
Was this helpful?
Thank you for voting!
Bake element broken
1 of 2 people found this instruction helpful.
  • Charles from Damascus, MD
  • Easy
  • Less than 15 mins
  • Wrench (Adjustable)
Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.

I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven . I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.

I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.
Was this helpful?
Thank you for voting!
Baking element burned through.
1 of 2 people found this instruction helpful.
  • James from Seattle, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."

Disconnecting the two wires and recon necting them was a simple operation after I cleaned my pants from the electrical short.

Re attaching the two-screw panes to hold the element in place finished the project.
Was this helpful?
Thank you for voting!
burned out
1 of 2 people found this instruction helpful.
  • David from Woodbridge, VA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.
Was this helpful?
Thank you for voting!
Oven wouldn't heat bottom
1 of 2 people found this instruction helpful.
  • Thomas N from Blackfoot, ID
  • Really Easy
  • Less than 15 mins
  • Nutdriver
.First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and reversed the procedure with the new element very simple.
Was this helpful?
Thank you for voting!
Old unit was bent and didn't work properly
1 of 2 people found this instruction helpful.
  • Christine from Danbury, NC
  • Really Easy
  • Less than 15 mins
I unplugged the old unit and plugged in the new one! It works.
Was this helpful?
Thank you for voting!
coils with tips damaged
1 of 2 people found this instruction helpful.
  • Jose from The Woodlands, TX
  • Really Easy
  • Less than 15 mins
it was very easy, a few seconds and new range for a cuople of years more!
Was this helpful?
Thank you for voting!
heating element shorting out-sparking
1 of 2 people found this instruction helpful.
  • K from PERRYVILLE, MO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I turned off electric to the stove. In the oven, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. After unpacking the new element, I placed it in the bottom of the oven, reconnected the two wires, and gently fed the wires back into the back of the oven. I then secured the new unit to the oven wall with the two screws.
Was this helpful?
Thank you for voting!
All Instructions for the 10392
76 - 90 of 285