103785 Kenmore Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Gas oven stopped working (no heat).
0 of 1 people
found this instruction helpful.
-
Jackie from Brunswick, ME
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
The range still worked and the broiler still worked. I noticed that the ignitor for the broiler turned on and glowed a short time after starting the broiler. I dissembled the floor of the oven (just two screws) and tried the same for the oven, but the ignitor did not start or glow. I ordered the part. It was sent withing two days. It
... Read more
was easy to replace and the oven has worked well since. I recommend ordering the attachment fixture as well, in that taking apart the one that held the old ignitor immediately stripped a screw and I ended up bending the fixture and having to reshape it (the small extra cost will be very well worthwhile!)
Read less
Was this helpful?
Thank you for voting!
lower igniter dead
0 of 1 people
found this instruction helpful.
-
Glen from Medford, MA
- A Bit Difficult
- 15 - 30 mins
With directions from the website as well as in the box, the repair was almost flawless. I needed to be a mouse with a 6mm box-end wrench.
Was this helpful?
Thank you for voting!
Oven bottom burner would not light
0 of 1 people
found this instruction helpful.
-
Doreen from Lansdale, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I removed the bottom drawer, disconnected the wires and then using the socket driver removed the screws holding the burner in place from below. I then unscrewed the bottom plate of the oven from the top so I could get to the burner. I unscrewed the one screw still holding the burner in place. Disconnected the old igniter and then cut t
... Read more
he cables at an appropriate length so I could re-use the connectors on new igniter. Spliced together using wire nuts provided, mounted new igniter to burner, put it all back together and it fired up like it was new.
Read less
Was this helpful?
Thank you for voting!
oven igniter quit working
0 of 1 people
found this instruction helpful.
-
Paul from New Hampton, IA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I removed the oven grates and removed 2 screws that held the bottom pan in the oven to get easy access to the burner and igniter. Remove 2 screws that held the burner in place. Removed wire nuts. Removing burner allowed easy access to fasteners holding ignitre in place. Confirmed that the igniter was bad by checking the continuity. Or
... Read more
dered part later in the evening from parts select. Part was here 2nd morning after I ordered it. Installed, and checked to make sure igniter wasworking properely. When check confirmed igniter was working, replace oven components. Saved myself $100 or more by doing it myself rather than having a repairman out.
Read less
Was this helpful?
Thank you for voting!
Oven refused to light checked all connections suspected the igniter was bad
0 of 1 people
found this instruction helpful.
-
Robert from lebanon, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver
Removed bottom drawer removed door and racks and bottom shield.disconected two leads from igniter . then struggled to remove igniter. after ordering part readf comments from other men and the man who said he removed the burner hit it right on the head after the part arrived the very next day after ordering it i removed the burner attached
... Read more
pig tails and had part installed and stove back together in 15 minutes. thanks good experience
Read less
Was this helpful?
Thank you for voting!
Igniter would not go on to lite the burner
0 of 1 people
found this instruction helpful.
-
joseph from Ozone Park, NY
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
took the bottom plates off with philips screwdriver.(note) there are two plates..outter and inner..to get to the two screws on the igniter.Remove igniter(two nuts). Install new. Cut the wires from old(lower part of oven and rewire with porclain wire nuts.Very simple...Partselect was great too..very fast shipping. Will do buisness again.
Was this helpful?
Thank you for voting!
broiler worked but oven didn't
0 of 1 people
found this instruction helpful.
-
Mary from Pekin, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver
We follow the advise of one of you other viewers. It was so easy. Our thanks for the info and the speeding delivery
Was this helpful?
Thank you for voting!
oven would not light.
0 of 1 people
found this instruction helpful.
-
Thomas from Port Huron, MI
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I removed the oven burner while the igniter attached. put unit on my bench and changed the igniter and reinstalled the burner and reattached the wires to the supply terminals. Tested the unit and it lite up ok.
Was this helpful?
Thank you for voting!
oven without heat
0 of 1 people
found this instruction helpful.
-
karen from Chicago, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver
Took off the 2 bottom covers, saw the igniter did'nt glow, checked for voltage,yes.Ordered part. when had part,pulled out ignitor,respliced wires, and did in reverse order.
Was this helpful?
Thank you for voting!
Igniter didnt work
0 of 1 people
found this instruction helpful.
-
Philip from Lyndhurst, NJ
- A Bit Difficult
- 15 - 30 mins
-
Socket set
I took out the racks, unscrewed the bottom cover, removed the bottom drawer, cut the leads for the igniter, removed the bad one, had a little difficulty installing the new one, the screws were a little longer than the old ones, and were a little hard to get at, rewired the the leads, and put everything back, and started it up and it worke
... Read more
d great!
Read less
Was this helpful?
Thank you for voting!
igniter burned out
0 of 1 people
found this instruction helpful.
-
Dwight from Angola, NY
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
followed peoples advices and all went very smooth. make sure to undo bracket from behind bottom drawer as it will make your life much easier.
Was this helpful?
Thank you for voting!
The electric igniter wore out - broiler burner
0 of 1 people
found this instruction helpful.
-
Andrew from Woburn, MA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I open the oven, then pulled out the racks. I went on to remove the bottom pan by removing 2 screws from the back.. I then removed the broiler burner and disconnected the wires from the relay. I unscrewed the igniter and replaced it. I stripped the wires and connected the old connectors using the ceramic wire nuts. I put the burner
... Read more
back in place and connected the wiring.. I then trested the unit to make sure it worked . . .it did. I replaced the bottom pan and racks and once again made sure everything was working right.
Job done.
Job done.
Read less
Was this helpful?
Thank you for voting!
Oven would not light
0 of 1 people
found this instruction helpful.
-
Robert from Joliet, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I removed the oven door, racks, and oven floor. That was easy, the floor had two thumb screws and one phillips/hex screw. I removed the lower drawer and the 2 covers above the drawer. The igniter was held in place by two phillips/hex screws. Had to manuver a bit to get the right angle to remove the screws. THE MOST IMPORTANT PART OF
... Read more
THE REPAIR, when you cut the two wires to remove the old igniter, cut them off as close to the old igniter module as possible. On my stove one of the wires on the new igniter was about an inch too short and I had to add a section of wire. Overall the whole job was easy. Keep track of screws as you remove them.
Read less
Was this helpful?
Thank you for voting!
The oven would not heat.
0 of 1 people
found this instruction helpful.
-
Gloria from Edmond, OK
- Really Easy
- 15 - 30 mins
-
Screw drivers
We found the part right away from the diagram provided by your web site. We located the part number easily, paid on line and received in part in two days. My husband fixed it. It was relatively easy. Saved us money to pay someone to fix it. It could easily cost us more than $200.
Was this helpful?
Thank you for voting!
Sunday night 4 days before thanksgiving oven wont light
0 of 1 people
found this instruction helpful.
-
Nicholas from Palmyra, NY
- A Bit Difficult
- 15 - 30 mins
-
Wrench set
Part arrived day before thanksgiving bent old igniter back and forth till broke off then easily took out screws.Cut and strip old wire, screw on new ignighter this was tough to get a wrench on with the positioning but after connecting those wires and slappin the rest of the oven back together one turn of the temp knob told me thanksgiving
... Read more
was going to happen Thanks to part select I was lookin like a hero!
Read less
Was this helpful?
Thank you for voting!