10363 Kenmore Range - Instructions

Removed old broken element and installed new one. Took less than 10 minutes

I ordered a new drip pan. Piece of cake. Stove looks new again.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Installed easily, was most impressed with the speed of delivery and it was the perfect size!!

All I had to do was just unscrew the bolts,pull out the old one, and put the new one on its metal clips and then rebolt.So easy and I know I would have had to pay much more then what I did for the part..This place is super.I ordered my part one day, and it was there the next...Sandy

Instead of flipping circuit breaker, we pulled the oven away from the wall and unplugged it. Used socket wrench to loosen screws of bracket holding old element onto the back oven wall, then gently pulled element until connecting wires appeared. Removed the 'clips' attached to the old element prongs and discarded old element. Reattached ... Read more the 'clips' to new element prongs, then gently pushed prongs into back into oven wall until the bracket was flush with the wall. Used socket wrench to screw and tighten the bracket into place. Plugged in the oven and tested the new element to make sure it worked. The whole process took only a few minutes.....it took longer to clean the oven before installing the new element.

Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to ... Read more swap out the parts and... success!
Don't forget to turn off the circuit breaker before starting repairs.

First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."

Disconnecting the two wires and recon ... Read more necting them was a simple operation after I cleaned my pants from the electrical short.

Re attaching the two-screw panes to hold the element in place finished the project.

Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.

I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven ... Read more . I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.

I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.

Quick and easy, thanks!

.First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and reversed the procedure with the new element very simple.

My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.

I unplugged the old unit and plugged in the new one! It works.

it was very easy, a few seconds and new range for a cuople of years more!

Easy