10336 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Igniter wouldn't turn on to ingnite the oven
1 person
found this instruction helpful.
-
Peter from Lyndhurst, NJ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
It was a simple repair removed the oven door, and the oven bottom plate. removed the screw that held the burner tube to gain access to the two screws that hold the igniter in place clipped the wires. put the new one on with butt end wire connectors instead of the wire nuts supplied. screwed the igniter back onto the burner tube put the bu
... Read more
rner tube back in place and secured it with the screw, replace oven bottom and door the whole repair took 20 minutes.
Read less
Was this helpful?
Thank you for voting!
Broil would work, but bake wouldn't
1 person
found this instruction helpful.
-
Patricia from Bellevue, WA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
IThe schematics on the website were helpful for how everything goes together. I just followed the picture and then unscrewed all the screws that held the ignitor to the gas pipe. Have to pull out the gas pipe out first so you can get to the bolts, easy to do when you pull out the drawer and unscrew the hold down for the gas pipe.
< ... Read more br />No directions came with the part, and the length of the new wires weren't long enough nor did they have the attachment pieces that are needed to plug in the wires. However, helpful tips from others on the website told me that you have to cut the wires off the old part and screw the wires from the old to the new with the white plastic wire couplings. Worked like a charm!
It was a simple procedure, and I saved myself buying a new stove or paying someone else to fix it!
< ... Read more br />No directions came with the part, and the length of the new wires weren't long enough nor did they have the attachment pieces that are needed to plug in the wires. However, helpful tips from others on the website told me that you have to cut the wires off the old part and screw the wires from the old to the new with the white plastic wire couplings. Worked like a charm!
It was a simple procedure, and I saved myself buying a new stove or paying someone else to fix it!
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat
1 person
found this instruction helpful.
-
ERIK from MADERA, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver
I removed the bottom pan and then removed the flame extender to get access to the igniter. I removed the two screws and cut the wires. I then wired the new igniter and used the ceramic wire nuts that came with the part. After that I installed the igniter. It was very easy to do this repair.
Was this helpful?
Thank you for voting!
Gas oven would not light
1 person
found this instruction helpful.
-
Dwight from Houston, TX
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
I was able to access the burner and igniter by removing the broiler drawer. The flame guard was removed with a nut driver and the old igniter with a phillips screwdriver.
The electrical wires had to be spliced into the old igniter wires as they did not come with the factory connectors. However sire nuts were supplied.
... Read more r />After replacement of the igniter with the new one .. it would glow and about a minute later the gas would come on. However the gas from the burner did not light. I had to adjust the bracket closer to the burner to correct the issue.
Note: The igniter is wired in series with the gas valve. This means that it will continue to glow even after the burner lights durning oven operation.
The electrical wires had to be spliced into the old igniter wires as they did not come with the factory connectors. However sire nuts were supplied.
... Read more r />After replacement of the igniter with the new one .. it would glow and about a minute later the gas would come on. However the gas from the burner did not light. I had to adjust the bracket closer to the burner to correct the issue.
Note: The igniter is wired in series with the gas valve. This means that it will continue to glow even after the burner lights durning oven operation.
Read less
Was this helpful?
Thank you for voting!
Oven did not light
1 person
found this instruction helpful.
-
Steve from Houston, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
I figured out the problem, ordered the part, and replaced it. Four hex head screws, two wire nuts, and two thum screws latter it was working.
Was this helpful?
Thank you for voting!
broiler woks ,bake doesnt
1 person
found this instruction helpful.
-
HEIDI from NEW ROADS, LA
- Easy
- 15 - 30 mins
-
Socket set
i went for 3 months waiting on the electrician who never came then asked the plumber who else could fix it and he said my husband could it only needed to unscrew 4 tiny screws and unplug and cut and twist wires back the hardest part was reaching the bolts hooked to the ignighter the burner was in the way and is not as easy to remove as so
... Read more
meone has said all in all it saved us 100 dollars and could have saved us months of burning food trying to cook on broil if i had only called the plumber first.ha ha
Read less
Was this helpful?
Thank you for voting!
The oven igniter burned out.
1 person
found this instruction helpful.
-
Michael from Las Vegas, NV
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I rempved the top and bottom doors, than the wire rackes followed by the bottom base of the oven. Then I removed the burner cover plate so I could get to the igniter.. I removed the cover plate for the wiring (2 wires), unpluged them, removed the igniter (2 screws). I had to cut the wires on the old igniter and couple the ends to the new
... Read more
igniter and then replaced everything by just reversing all that I did. Simple! Easy!
Read less
Was this helpful?
Thank you for voting!
Our oven would not lite
1 person
found this instruction helpful.
-
Kirk from New Castle, DE
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
First shut down electric power to oven. remove
oven racks and botton tray. Removed boiler rack and door. Next unscrew 2 bolts holding igniter. remove nuts or cap for two white electric wires.
installed new igniter, hooked backup wires. replaces racks and tray and that was it, job done.
oven racks and botton tray. Removed boiler rack and door. Next unscrew 2 bolts holding igniter. remove nuts or cap for two white electric wires.
installed new igniter, hooked backup wires. replaces racks and tray and that was it, job done.
Was this helpful?
Thank you for voting!
Over not lighting
1 person
found this instruction helpful.
-
Anthony from DeKalb, IL
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Remove the front door-lifted off(no tools) removed the floor of the oven (2 standard nuts at the rear). nut driver to remove the igniter. Took longest to untwist and retwist wires & dropped screws. reassembled and tested...worked perfice. this is the 4th time I've used Parts Select and It's great....Thanks and keep up the good work!
Was this helpful?
Thank you for voting!
Oven would not light
1 person
found this instruction helpful.
-
Roger from Downingtown, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed the bottom plate inside the stove by removing two back screws. The burner was exposed. roved a total of three screws on gas burner to remove the entire assembly. Removed two screws from the old igniter and then put new one on. Save the old connectors because they have unique connectors. Cut old wire and strip 3/8 inch of wire cov
... Read more
er off. Using the supplied wire nuts. Caution use only supplied wire nuts because they are meant for heat. connect old wire to new wire of the new igniter. Reverse order of screws that you did for the job. That is it
Read less
Was this helpful?
Thank you for voting!
Bake didn't work, broiler did
2 of 4 people
found this instruction helpful.
-
Bill from Harleysville, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Unplugged the oven. First i removed the 2 screws from the pan at the bottom of the oven and took the pan out. Next i took out the drawer underneath and took the screws out of the pans below to get to the ignitor. Unscrewed the ignitor and cut the wires below it to splice the new ignitor on. Spliced the two sets of wires and put the cerami
... Read more
c wire nuts on. Replaced the top and bottom pans and put the drawer back. plugged the oven back in and started the oven right up. Pretty easy.
Read less
Was this helpful?
Thank you for voting!
Igniter coil burned out
1 person
found this instruction helpful.
-
Chuck from Los Angeles, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
- removed the oven unit from the wall
- removed the aluminum backplate to expose the wiring
- Removed both glass wire nuts and disconnected the heating element\
- From the front, I removed both retainer screws and pulled the element wires through.
- In reverse order I reinsalled the new wires and screwed on the heating ... Read more element.
-I reattached the electrical wiring and rear pane.
- I re-installed the unit into the wall.
- removed the aluminum backplate to expose the wiring
- Removed both glass wire nuts and disconnected the heating element\
- From the front, I removed both retainer screws and pulled the element wires through.
- In reverse order I reinsalled the new wires and screwed on the heating ... Read more element.
-I reattached the electrical wiring and rear pane.
- I re-installed the unit into the wall.
Read less
Was this helpful?
Thank you for voting!
Burned out
1 person
found this instruction helpful.
-
John from GLENVIEW, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Go to utube videos for this are there
Was this helpful?
Thank you for voting!
Igniter stopped working
1 person
found this instruction helpful.
-
Arkady from Chicago, IL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
1. I have searched info on the internet and found that site.
2. Initially I could not figure out how to unscrew ingniter. After reading more post I have found out how to access nuts underneath.
3. After I have removed lower drawer and unscrewed metal cover and then inginter nuts.
4. I have got a part with two wires attached ... Read more to the igniter and two porcelan insulator, so it was very easy to cut old wires and connect with an igniter wires in parallel
/||\
||
2. Initially I could not figure out how to unscrew ingniter. After reading more post I have found out how to access nuts underneath.
3. After I have removed lower drawer and unscrewed metal cover and then inginter nuts.
4. I have got a part with two wires attached ... Read more to the igniter and two porcelan insulator, so it was very easy to cut old wires and connect with an igniter wires in parallel
/||\
||
Read less
Was this helpful?
Thank you for voting!
bottom burner would not ignite
1 person
found this instruction helpful.
-
David from Truchas, NM
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
First i removed the inside bottom of the oven where i could get to the actual glow plug igniter and removed the two screw that held the igniter in place. I than pulled the entire oven out allowing me to access the two wires connecting the igniter to the stove. I disconnected the wires and had to splice the wires as to be able to reach
... Read more
the appropriate connections. I reinstalled the igniter and upon testing the igniter worked properly. The entire process took me one hour.
Read less
Was this helpful?
Thank you for voting!