020333-3 Briggs and Stratton Pressure Washer - Overview
Sections of the 020333-3
[Viewing 2 of 2]
Keep searches simple, eg. "belt" or "pump".
Kit-retainer Clips
PartSelect #: PS8907531
Manufacturer #: 195964GS
This authentic manufacturer-supplied part is specially designed for use with Briggs and Stratton, Troy-Bilt and Snapper pressure washers. It is a special hardware that helps to secure components. This...
$8.95
Special Order
Fuel Valve With Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
This is a genuine replacement part sourced directly from the manufacturer. The valve fuel kit is commonly found in Craftsman pressure washers and generators. This part includes the valve made of hig...
$33.95
Special Order
18oz 30w 4 Cycle Oil
PartSelect #: PS8817222
Manufacturer #: 100005
This bottle of oil can be used in over 150 different types of machinery. It is most commonly used for pressure washers and generators from manufacturers such as Briggs and Stratton and Troy-Bilt. This...
$8.95
In Stock
Pump Saver Kit - 4oz
PartSelect #: PS9042654
Manufacturer #: 6039
This is an authentic OEM part from Briggs and Stratton, Troy-Bilt, and Snapper for use with Pressure Washers. The Briggs & Stratton Pressure Washer Pump Saver prevents harmful buildup of hard-water mi...
$21.95
Special Order
Kit, Handle Fastening
PartSelect #: PS9181264
Manufacturer #: B2203GS
This is a genuine item that is supplied directly from the original equipment manufacturer for use with Troy-Bilt and Briggs and Stratton pressure washers. It is an identical replacement for a missing ...
$9.95
Special Order
Wand, Hi-lo
PartSelect #: PS9270235
Manufacturer #: 205015CGS
This is an authentic OEM part for use with Craftsman Pressure Washers. The wand connects to the spray gun handle and houses the nozzle that directs the spray stream. The most common reasons for replac...
$126.95
Special Order
Pressure Washer Pump Assembly
PartSelect #: PS9270371
Manufacturer #: 207365GS
Pressure washer pump kit. If the pressure washer is leaking water, the pump may need to be rebuilt or replaced. If the pump is more than a few years old, and you use the pressure washer fairly often, replace the pump.
$444.95
Special Order
Thermal Relief Valve
PartSelect #: PS9270416
Manufacturer #: 208673GS
This genuine OEM sourced replacement part is designed for use with pressure washers. If the pressure washer runs too long with out the release of water from the sprayer, the water will heat up inside ...
$27.95
Special Order
Common Symptoms of the 020333-3
[Viewing 2 of 2]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Parts Used:
-
John from LEES SUMMIT, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
9 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!