Order within the next 45 mins and your part ships today!
Fits your ADB1400AGW3!
About This Part
What it does. Why it matters. Everything you need to know for an easy fix.
Dishwasher Heating Element Specifications
This manufacturer-certified heating element is used to create heat during the dry cycle and increase water temperature during portions of the wash cycle when certain options are selected. If your dishes are not drying or the water in the dishwasher is not getting hot you may need to replace the element. This kit includes the heater, two heater fasteners, and is a genuine OEM part. Please remember to disconnect the power before starting the repair. Use a multi-meter to test your heating element for continuity to determine whether this is the part that is causing your symptom. This part does not include any washers. To make your repair, disconnect the wires from the bottom of the element in the back, remove the plastic nuts holding it in place, remove the element, and repeat these steps in reverse order to install your new part. This is an easy repair that requires only a screwdriver, wrench set, and should take less than 30 minutes.
Part #W10518394
Manufactured by
Whirlpool
for Whirlpool, Kenmore, Maytag, Amana
Real ratings from other people who bought this part.
Average Rating:
★★★★★
★★★★★
72 Reviews
4.8
Out of 5
5 Stars
65
4 Stars
4
3 Stars
1
2 Stars
0
1 Star
2
Search reviews left by others. DIY doesn't mean you have to do it alone. Use simple keywords like "fit", "broken", "easy", or "quality" to find reviews that match!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Paula B - August 10, 2022
Verified Purchase
Shipped quickly. Works as expected.
Extremely well packaged part arrived much quicker than expected. Worked and resolved issue.
★★★★★
★★★★★
John R - February 25, 2023
Verified Purchase
Worked!!!
Great site
★★★★★
★★★★★
Vincent T - August 22, 2019
Verified Purchase
Perfect and an easy repair !
Fit perfectly and it's an easy repair to do it yourself. You will need to know how to make a diagnostic cycle on you dishwasher so it recognize the new element and use it.
★★★★★
★★★★★
Roberta B - August 5, 2020
Verified Purchase
Dishwasher is back in service!
The dishwasher heating element arrived in 2 days to us on Vancouver Island! Thank you!
★★★★★
★★★★★
Chantall S - April 20, 2025
Verified Purchase
Perfect Part
The part arrived in perfect condition. Hired a professional to put it in as we’ve had previous issues with the placement of the dishwasher under the counter. Element works exactly as it should.
★★★★★
★★★★★
Eric B - October 22, 2020
Verified Purchase
easy repair
the part was in great condition and doesn't take long to have it.
★★★★★
★★★★★
Robin C - June 22, 2026
Verified Purchase
Prompt delivery and easy repair
We received this replacement heating element shortly after ordering it. We are not a handy household, but this repair was relatively straightforward and the part seems to be working great after several subsequent uses of our dishwasher.
★★★★★
★★★★★
Eileen O - April 20, 2023
Verified Purchase
Dishwasher heating element repair...so easy!
Excellent service. The part was exactly what we needed. My husband replaced it himself without the cost of a service call, and the dishwasher is in full working order.
★★★★★
★★★★★
Rishard O - April 30, 2021
Verified Purchase
Works great
No problems with the part. Service is as always fantastic. R
★★★★★
★★★★★
Mitchell T - January 19, 2020
Verified Purchase
Easy
My part can quicker than I thought and was an easy repair.
Prev
1
2
3
Next
Repair Tips
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
Easy
30 - 60 mins
Average repair rating from 33 real customers like you
Sort by:
Prev
1
2
3
Next
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sorry, we couldn't find any existing installation instruction that matched.
Heater element broken.
238 of 282 peoplefound this instruction helpful.
Dennis from Sedro Woolley, WA
Really Easy
Less than 15 mins
Screw drivers, Wrench set
Step 1: Remove the screws in the bottom of the countertop.
Step 2: Remove the screws holding the bottom kickplate.
Step 3: Loosen leveling legs.
Step 4: Pull dishwasher out of hole.
Step 5: Unlplug dishwasher.
Step 6: Disconnect wires from bottom of element in back.
Step 7:
... Read more Remove plastic nuts holding element in place.
Step 8: Remove element.
Step 9: Reverse Steps 1-7.
Step 10: Drink beer.
Read less
Was this helpful?
Thank you for voting!
Unit Wouldn't Work. "Clean" Light Blinking
108 of 150 peoplefound this instruction helpful.
PAUL from ESTES PARK, CO
Really Easy
1- 2 hours
Nutdriver, Screw drivers
The unit had power, but the controls would not work. The "clean" light was blinking. I first replaced the control unit, no help. I then used the "just ask" and was told the problem was the heating element and/or the hi-temp thermostat. I replaced both those and used the re-set code pushing the "hi-temp/air dry, hi-temp/air dry" button
... Read mores. That did it. Easy parts to locate and replace. It took longer pulling the unit out and putting it back than it did to replace the parts.
I released the heater element from the clips on the bottom of the waaher tub. I pulled the unit out from the wall and disconnected power. There are two slip on wire terminals on each end of the heater element accessible from the back that need to be removed. One of them was badly rusted from leaking water, which had caused the short, a
... Read morend had to be replaced. These terminals and the crimping tool to install them are available at any home center. I removed and discarded the old plastic nuts since one of them was damaged by arching from the short circuit. Moving around to the front of the dishwasher, I removed the old heater and installed the new one. I had ordered new rubber washers, but the new heater came with them already installed. Since one of the old ones failed and caused the leak, they are a good thing to keep around as spares anyway. I installed the new nuts and tightened them to enough to ensure that the washers made a good seal. I reconnected the wire terminals to the heater, reconnected power and moved the unit back into place. The circuit opening when the heater failed caused a "call for service" error and the controller would not allow the unit to run. You will know you have this by the "CLEAN" LED flashing seven times. Clear the diagnostics by pressing the buttons for "HEATED DRY", "NORMAL", "HEATED DRY", "NORMAL" and after the controller resets, the dishwaher is ready to run. It's worked like new ever since.
Turned off power, turned off water supply and diconnected, slid out dishwasher. Removed the spray wand and tilted dishwasher to access the two nuts and disconnet the wires. Removed the two nuts using a socket. Removed the old heating element and replaced with the new one secured with new nuts ( the old ones were fine but since I bought tw
... Read moreo new ones why not). Pluged the wires back up slid the dishwasher back in hooked up the water reinstalled the spray wand cut on the water and power. Good as new.
removed screws holding dishwasher to counter top,raised leveling pads,pulled dishwasher out, unplugged wiring,removed hold down nuts from inside dishwasher and installed new heater element, this was all easy the hard part was finding the code to reset the dishwasher there was no paperwork inside the dishwasher although there was an empty
... Read moreplastic holder.The code that worked for my model was with the door open to push the normal wash button then the high temp button three times as fast as you can within four seconds then close the door. It worked and reset the dishwasher which ran a short cycle then shut down as normal and is now working fine.After doing this select the beverage of your choice and relax. Hope this helps someone.
Read less
Was this helpful?
Thank you for voting!
Dishwasher wouldn't heat water or dry dishes
16 of 19 peoplefound this instruction helpful.
Philip from Sugar Land, TX
Really Easy
15 - 30 mins
Pliers, Screw drivers, Wrench set
Disconnected the power and hot water supply. Removed mounting screws under the counter, and the lower panel screws to expose the leveling screws. Backed the leveling screws up so that the unit would slide out more easily Walked the unit out to where I could reach the back side. Disconnected the two power wires from the
... Read more heater coil (slide off) Unscrewed the plastic nuts holding the heater in place and removed the heater coil. Replaced the heater coil and nuts. Reversed the process above to install.
Very easy repair !!! I ordered my heating element on a Friday , it was on my porch Saturday. I used the directions that Parts.com sent me . I also read everyones Installation instructions ..... Every step was very easy . I did watch a utube video , so I couldn't screw this repair up......... My wife had a new dishwasher picked out for
... Read more $ 579.00 , my part was $29 dollars , savings $550 dollar ...... After the repair , I ran the dishwasher and the blinking clean lite took care of itself ... The water has never been this hot and dryers the dishes like it was a new dishwasher ...... My advice , read everyone's Installation instuctions and watch the utube video .....
Read less
Was this helpful?
Thank you for voting!
Heater element broke inside washer
9 of 13 peoplefound this instruction helpful.
KS from Garland, TX
Really Easy
15 - 30 mins
Wrench (Adjustable)
I pulled the unit away from the cabinet, unplugged the washer and water line(not long enough to reach) removed two nuts from the underside and replaced the heating unit.
The repair was easy. Getting the unit to slide out from under the counter was more time consuming. After water and power is disconnected, tip the unit over onto one side to gain access to bottom. Look for two white composite plastic posts (insulators) about 2" long each with a single wire inside. Remove the two wire connectors then
... Read more unscrew the insulators from the old heating element using an adjustable wrench. Inside the box remove the two metal element supports and pull out the old element. Clean and dry the area in and around the openings where the new element will be re-inserted. Carefully place the new element into the holes with the included new rubber washers. Re-install the two metal element supports on the inside of box. On the bottom, re-install the two insulators to the ends of the element, do not to tighten too much to avoid over compressing the rubber washers which could cause premature cracking. Reconnect both wires and check continuity from the door mircro-switch (white-violet) lead to the (white-red) lead on Electronic Controller connector #1 (P6). The circuit thru the element should be good if the Multimeter reads 10-35 ohms. Put the unit securely back under the counter and run a test wash. Works fine now. I do recommend, if don't know how to use a multimeter or are concerned about accessing the electronic control box; contact a professional.
Read less
Was this helpful?
Thank you for voting!
The dishwasher would not dry (heat)
7 of 11 peoplefound this instruction helpful.
Glenn from Daleville, AL
Easy
15 - 30 mins
Screw drivers, Wrench (Adjustable)
First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly. Nothing to it. I
... Read more then had to reset the error code and it is working like new.
Read less
Was this helpful?
Thank you for voting!
Prev
1
2
3
Next
DIY Questions and Expert Answers
59 questions answered by our Repair Experts.
Ask our experts a question about this part and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeff - For model number KUDS30IVWH3
December 19, 2018
How do you check the heating element for continuity?
Hello Jeff, thank you for your question. To test the element, locate your dishwasher's heating element. Open the dishwasher door and look into the tub. It is the thin, circular tube at the base of your dishwasher. It may or may not be covered. If it is covered, remove the lower dishrack, and then remove the cover.
Your heating element is going to have two metal terminals. One at each end. Each terminal reaches downwards, into the base of the dishwasher. Mentally mark the area where each terminal enters the base of the tub.
Now you need to gain access to the heating element's wiring. You can do this by first removing the lower kickplate panel of the dishwasher. There will be at least two screws (but maybe four) holding the kickplate panel in place. They are located either on the top or the bottom of the panel. If the screws are located on the top, you may need to open the dishwasher door in order to gain access to them. Close the door to remove the panel, though.
Now look into the lower access area that you have just uncovered. Pinpoint the area where the heating element terminals extend through the base of the dishwasher. They will each have a wire connected to it. Label each of the wires so that you will be able to properly reconnect them later. Now you can pull the wires off the terminals.
Each wire is connected to a terminal using a slip-on connector. Grasp the connector and pull on it firmly. DO NOT pull on the wire itself. Pull only from the connector. You may decide you need to use a pair of needle nosed pliers to help you.
Use your multitester (aka multimeter) to test the heating element for continuity. Set the device to the ohms setting x 1. Touch each meter probe to a terminal. You should receive a reading somewhere in between infinity and zero. Because of the variety of makes and models of dishwashers, it is quite difficult to say exactly what the reading should be for each and every possible model. However, if the test you conduct produces a reading of infinite resistance (meter's needle does not move), then that is indicative of a faulty heating element, and you should replace yours. Similarily, if the test you conduct produces a reading of zero resistance (meter's needle moves to the other extreme of the scale), then that is also indicative of a faulty heating element, and you should replace yours.
You do not have to remove the heating element from the dishwasher in order to test it. Just make sure power is not getting to your dishwasher before you conduct the test. I hope this helps!
65 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Russ
December 9, 2017
Whirlpool dishwasher heating element has a 6” setting glowing red. Is this normal?
Hello Russ, Thank you for your inquiry. Yes, this is normal. Have a nice day!
25 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Greg - For model number GU1100XTLB1
December 20, 2017
Does this heating element include the rubber washers that seal the element to the tub?
Hi Greg,
Thank you for your question. The rubber washers are sold separately. The part number for the washers is PS11743934. I hope this helps. Thank you and have a great day!
17 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Alex - For model number WDF310PAAS4
December 6, 2017
Replaced the heating element but it does not seem to heat up on my Whirlpool dishwasher. Connected the leads to same orientation as before. Is there a switch or cut off that would keep power from the heating element?
Hi Alex,
Thank you for your question. If the heating element is not working, you may have to check to see if the issue with the high limit thermostat. This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element. I hope this helps. Thank you and have a great day!
10 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Tracie - For model number WDT710PAYM6
April 21, 2018
My dishwasher works great but does not dry dishes on the top rack. What can i do to fix this problem?
Hello Tracie, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: inner door vent, heating element, and high limit thermostat. You can test the element and thermostat with a multimeter. Hope this helps!
10 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Dave - For model number WDF520PADM3
December 31, 2017
Lights are on display when pressing start nothing happens and lights stay on noticed d w hasn't been turning on regularly last few days could be the heating element? Or? Thanks
Hello Dave, Thank you for your inquiry. I would check the heating element, the high limit thermostat and the turbidity sensor with a multimeter to see if they have continuity. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!
9 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Lou - For model number ADB1400AGS1
January 20, 2020
I need the heating element for this Amana dishwasher. Is this the correct one? If so, do i need to purchase any other parts? My dishwasher model number is adb1400ags1.
Hello Lou, thank you for your question. The element is PartSelect Number: PS8260087. This is the correct replacement part. You should not need any other parts to complete this repair.
8 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Frank - For model number WDT710PAYM5
January 26, 2018
Hello, I am in need of the heating element for this model. I see your PS8260087 is noted on your website as the part, can you please tell me if this is an OEM part or aftermarket?
Hello Frank,
Thanks for your question. Yes, this part is the correct heating element for your model and it is OEM.
I hope this helps.
6 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Bruce - For model number WDF530PLYW2
March 14, 2018
-ok, i tested all three parts as mentioned in your answer below and they all have continuity (the meter "beeeeped" when i touched each part's poles). I carefully put everything back together, turn the power back on and ... nothing. no lights. nothing. any other ideas?
-----++ hello bruce, thank you for your question. the first parts to check would be the door latch, door latch - black part number: w10619006 to see if it is faulty. if the switch isn't working the signal will not be sent to the board to let it know that its safe to start the cycle. you will also want to test the high limit thermostat part number: wp661566 and turbidity sensor part number: wpw10705575. if these are tested and the unit is still not powering up, the problem is most likely the electronic control board part number w10473200. i hope this helps!
Hi Bruce,
Thank you for your question. If you have have tested all the parts including the electronic control board, then you will need to contact then you will need to contact a technician to come out and check to see what is going on with your appliance. I hope this helps. Thank you and have a great day!
6 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Dedra - For model number MDB4709PAW1
February 5, 2020
I ordered the element (part # w10518394) and it is too short. It is oval rather than the horseshoe style that is in the dishwasher. The one needed is approximately 15” in length. Do you have the correct element?
Hello, Thank you for your question. Looking at your model number here is the correct element for your model. Part #: PS8260087. We hope this helps, good luck with this repair.
6 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Prev
1
2
3
Next
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Item is in stock and is estimated to be delivered in 2-3 business days via Standard Shipping.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Element or Burner","title":"Element or Burner","url":"/Dishwasher-Elements-and-Burners.htm"},{"position":2,"name":"W10518394","title":"W10518394","url":""}]
My Orders
