![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)
Product Description
Drum Bearing Slide - White (Sold individually) Specifications
This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if this part is an issue if your dryer is unable to tumble properly or is very noisy. Damage can come from regular use. The part attaches to the outermost side of the bearing. Check both slides for signs of wear, because they often wear at the same rate, and should be replaced at the same time; there are 2 of these particular slides per dryer. This part is sold individually, so you'll need to purchase multiple parts if replacing both at the same time.
![How Buying OEM Parts Can Save You Time and Money How Buying OEM Parts Can Save You Time and Money](https://img.youtube.com/vi/d6AvOkulk_g/maxresdefault.jpg)
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your General Electric Dryer Drum Bearing Slide - White (Sold individually)
![Replacing your General Electric Dryer Drum Bearing Slide - White (Sold individually) Replacing your General Electric Dryer Drum Bearing Slide - White (Sold individually)](https://img.youtube.com/vi/RDY-Gxh1D_s/maxresdefault.jpg)
Troubleshooting
This part fixes the following symptoms:
Noisy | Marks left on clothes
This part works with the following products:
Dryer, Washer Dryer Combo, Washer.
This part works with the following products:
General Electric, Hotpoint, Whirlpool, Kenmore.
Part# WE1M504 replaces these:
AP3206716, 963512, WE1M504, WE01M0333, WE1M333
Customer Reviews
Filter By Rating:
- < Prev
- 1
- 2
- 3
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Perry B - May 19, 2021
Verified Purchase
Fast, accurate and quality parts!
Ordered parts for my dryer, slides and full drum bearing. Parts Select made it easy to assist with diagnosis, and their instructional videos that are prompted by your online order are awesome! Thanks Parts Select!! Dryer is back in action.
Gustavo L - May 11, 2021
Verified Purchase
easy to replace, didn't improve performance as expected.
easy to replace, didn't improve performance as expected.
Gord W - April 13, 2021
Verified Purchase
Part if fine... ordering a bit unclear
The part is a piece of plastic, so not much can go wrong. Easy to install. That said, you likely need 2 to perform the job and it really should be flagged to say so.
Mike E - March 19, 2021
Verified Purchase
Repair very easy to do
Excellent video describing replacement procedure. Parts on dryer were worn and one was missing. Needed to be replaced. Suspect another problem as dryer still making same noise. Will pull apart and check parts.
Paul C - February 4, 2021
Verified Purchase
Service
It was a pleasure to do business with you. The service is good, and the parts arrived quickly to my door.
Don R - January 15, 2021
Verified Purchase
Noisy dryer
Part solved the problem
David M - October 7, 2020
Verified Purchase
Great transaction
Very timely delivery and exactly as described. Without being negative as this is probably beyond your control, but the slides are ridiculously expensive. Hopefully we will get many years out of them. Really like dealing with you and appreciate all the video aids.
WILLIAM S - September 19, 2020
Verified Purchase
Perfection
Loved the simple workings of the website. Gave % of likely failure & video showing how to install the part. The part arrived in two days. As good as it gets (didn't even try looking for a better price).
Daniel P - July 22, 2020
Verified Purchase
Worked as expected.
I always get a good service from Parts Select.
ROSE K - June 9, 2020
Verified Purchase
Easy repair
Perfect part
- < Prev
- 1
- 2
- 3
- Next >
Customer Repair Stories
Average Repair Rating: 3.7 / 5.0, 193 reviews.
What's this?
- < Prev
- 1
- 2
- 3
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
Other Parts Used:
-
Matthew from Plainfield, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
792 of 900 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer was squeeling when running.
I removed the two screws at the front above the drum opening (with the dryer door open). The top panel then lifts off. I removed the screw at each side that holds the front panel to the side panels, tilted the front panel forward, which disengages the front of the drum from the front drum glide bearing. I then lifted the front panel slightly, unhooking the bottom of the panel from the dryer base, and swung the front panel aside. I removed the existing top drum bearing guide, which was disintegrated, and snapped in the new bearing guide, with the nylon slide strips installed in the bearing guide. Next pulled out the old felt strip, and pressed the new one in place. I then put the bottom of the front panel back into the bottom of the dryer front, and while lifting the drum to asure it fit over the bearing guide, pushed the front panel back to a vertical position to mate with the side panels. I then replaced the side panel screws, replaced the top, and replaced the front top panel screws.
Other Parts Used:
-
Daniel from Chicago, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
703 of 792 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Intermittant squeaking noise
Basically, I followed the same steps a prior person posted.
1.Removed the two screws inside the door, on the top part of the opening.
2.Lifted up and removed the top.
3.Removed two screws holding the front panel in place.
4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at the drum bearing without pulling the wires connecting it to the front panel. The wires are not very long, so I had to be careful not to pull on them.
5.Carefully pried off the old drum bearing, using just my hands. It was fairly tight, and popped out just as I started to worry if I was putting too much pressure on it.
6.Checked to see how the old felt was installed, then I pulled out the old felt.
7.Inserted the new felt, being careful to insert one end into a slot the same way the original was installed.
8.Inserted the new slides into the new drum bearing. The gray slides went in at the eleven and one o'clock positions, the white slides went in at ten and two o'clock.
9.Removed a surplus plastic piece from the new drum bearing (where the light comes through).
10.Inserted the new drum bearing, putting the bottom tabs in first, then pivoting it into place. I squeezed it into place to make sure it was tight.
11.Lifted up the drum and put the front panel back on.
12.Screwed the front panel back on, using the two screws.
13.Carefully put the top back on.
14.Screwed in the two screws inside the front door to fasten down the top.
That was it! I started up the dryer and it worked fine. No more squeaking.
About the only thing odd about the repair is why PartSelect sells each slide separately (i.e., I had to order 2 white slides and 2 gray slides). I can't imagine replacing just one, so why not package them in pairs, or maybe even all four in one package.
At any rate, the repair was easy, and a lot cheaper than having someone come out to fix it.
1.Removed the two screws inside the door, on the top part of the opening.
2.Lifted up and removed the top.
3.Removed two screws holding the front panel in place.
4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at the drum bearing without pulling the wires connecting it to the front panel. The wires are not very long, so I had to be careful not to pull on them.
5.Carefully pried off the old drum bearing, using just my hands. It was fairly tight, and popped out just as I started to worry if I was putting too much pressure on it.
6.Checked to see how the old felt was installed, then I pulled out the old felt.
7.Inserted the new felt, being careful to insert one end into a slot the same way the original was installed.
8.Inserted the new slides into the new drum bearing. The gray slides went in at the eleven and one o'clock positions, the white slides went in at ten and two o'clock.
9.Removed a surplus plastic piece from the new drum bearing (where the light comes through).
10.Inserted the new drum bearing, putting the bottom tabs in first, then pivoting it into place. I squeezed it into place to make sure it was tight.
11.Lifted up the drum and put the front panel back on.
12.Screwed the front panel back on, using the two screws.
13.Carefully put the top back on.
14.Screwed in the two screws inside the front door to fasten down the top.
That was it! I started up the dryer and it worked fine. No more squeaking.
About the only thing odd about the repair is why PartSelect sells each slide separately (i.e., I had to order 2 white slides and 2 gray slides). I can't imagine replacing just one, so why not package them in pairs, or maybe even all four in one package.
At any rate, the repair was easy, and a lot cheaper than having someone come out to fix it.
Other Parts Used:
-
Mark from Addison, IL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
621 of 773 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer made LOUD screaching constant sound
(1) open dryer door (2) remove screws holding door on and put door aside. Probably doesn't have to be done but I think its easier and safer so you don't accidently bend the hinges. (3) remove 2 screws holding top onto front. of dryer located in recess that door sits in (3) pull up on top and remove (from slots by the control panel) (4) remove final 2 screws holding front onto frame of dryer. You can disconnect the connectors from the front panel back to the dryer to make the job easier or work with it without disconnecting. I'd take your time and clean any lint dust, etc. (5) the Drum Bearing removes fairly easy as it is just snapped into 2 slots. insert slids into slots.... make sure you order all 4. Mine were all beat!. (6) replace with new Drum Bearing. (7) I did the lower felt seal as well. Pay attention to how you took the old one off and replace the same way. Remember it stretches to fit into the slots. Put all back together. Remember to front panel has to sit correctly into bottom slots before you screw the top screws back in. All in all.... a simple project, and no more noise!!!!! Great to have websites like this. Easy ordering, quick shipping, great diagrams.
Other Parts Used:
-
Brian from Langhorne, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
269 of 425 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
LOUD - screeching noise during drying cycle, in all modes of operation.
1. Removed top cap on lid by removing the 3 - phillips screws.
2. removed front digital display panel from PC board.
3. removed bolts with nut-driver on the top of the front panel, removed bottom screws with #2 square bit.
4. removed "snap-in" plastic top bearing ( paying attention to where wiring is routed within this frame.
5. cleaned all areas of plastic and felt debris, installed new bearing, felt, and glides.
6. Re-installed all wiring and panels.
*** make sure to order all of the glides, there should be a total of 4 for the top assembly.
2. removed front digital display panel from PC board.
3. removed bolts with nut-driver on the top of the front panel, removed bottom screws with #2 square bit.
4. removed "snap-in" plastic top bearing ( paying attention to where wiring is routed within this frame.
5. cleaned all areas of plastic and felt debris, installed new bearing, felt, and glides.
6. Re-installed all wiring and panels.
*** make sure to order all of the glides, there should be a total of 4 for the top assembly.
Other Parts Used:
-
Bruce from Springfield, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
246 of 335 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
clothes having black marks and getting stuck on top of drum, tearing
Repair was easy, following the disassembly instructions from the video on your site. What I did not know is that it takes 2 pieces of plastic slides from each kind to replace (makes a total of 4). I was lucky in that one of the white ones was still okay and that I accidentally ordered a second one from the greenish kind, so I was set. This was also a great opportunity to clean out the dryer which must have been a bucket full of lint. So far no more complaints. Given that this problem seems to reappear once in a while I'll order a new set soon.
Other Parts Used:
-
Markus from Austin, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
170 of 248 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My clothes were being "bitten", discolored with blackish smudges, and buttons eaten off clothing
First I really had to hunt for the proper way to get my dryer drum accessible for the repair. With my model it was as simple as removing two screws to take off the top panel (located by opening the dryer door), and then removing two other screws inside the front panel at the top. The front will then be able to swing to the left side (the door switch wires are on this side for this model). Simply remove the drum bearing by gently pulling it off. My slides were in such poor shape for less than 4 years old!! One of them had completely disintegrated! These slides have a small whole on one end which attaches to a small nub at the edge of a slot while the other side just slid into a slot at the other end. No need to even take out the drum!!
The hardest part of the job was to get into the dryer!
The hardest part of the job was to get into the dryer!
Other Parts Used:
-
Deborah from Glenburn, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
91 of 105 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would squeal when first starting and then gradually became very noisey.
The repair was done as follows:
1. Removed the door
2. Removed the two screws securing the top panel then removed the panel.
3. Removed the two screws securing the front panel then removed the panel.
4. Removed the screws securing the left side panel then removed side panel and the two leveling feet.
5. Tipped dryer over on its back (you will want to protect your floor, the four screws that attach the heater unit protrude through the back).
6. Disengaged the belt tensioner and removed the belt and the drum.
7. Removed the three Torx screws securing the drum bearing to the drum and discarded old bearing.
8. Removed the four screws securing the bearing retainer to the heater unit.
9. Removed the four screws securing the heater unit and two sensor wires.
10. Lifted heater unit just high enough to remove bearing retainer. Discarded bearing retainer.
The new drum bearing kit is supplied with self tapping screws. I installed the screws into the bearing parts to tap the holes and then removed them prior to assembly.
11. Installed new bearing retainer to back of heater unit using the supplied screws. Install the four screws by hand, finger tight.
12. Re-attached heater unit and tighten screws.
13. Re-attached sensor wires.
14. Tightened the four bearing retainer screws.
15. Attached new drum bearing to drum using the three supplied Torx screws. I used tape to hold everything together while installing the screws.
Tightened the Torxscrews.
Next I used a vacuum to remove all the lint from inside the dryer. I also used a small plastic putty knife to remove the caked on lint on the impeller blades.
16. Inserted drum bearing into bearing retainer.
17. Installed drum belt and belt tensioner.
18. Installed left side panel and feet.
19. Replaced the two grey and two white slide bearings on the front panel. They just slip onto a small post and slide into a slot.
20. Installed front panel. (Rotate drum to help with installation)
21. Installed top panel and door
PROBLEM SOLVED!
1. Removed the door
2. Removed the two screws securing the top panel then removed the panel.
3. Removed the two screws securing the front panel then removed the panel.
4. Removed the screws securing the left side panel then removed side panel and the two leveling feet.
5. Tipped dryer over on its back (you will want to protect your floor, the four screws that attach the heater unit protrude through the back).
6. Disengaged the belt tensioner and removed the belt and the drum.
7. Removed the three Torx screws securing the drum bearing to the drum and discarded old bearing.
8. Removed the four screws securing the bearing retainer to the heater unit.
9. Removed the four screws securing the heater unit and two sensor wires.
10. Lifted heater unit just high enough to remove bearing retainer. Discarded bearing retainer.
The new drum bearing kit is supplied with self tapping screws. I installed the screws into the bearing parts to tap the holes and then removed them prior to assembly.
11. Installed new bearing retainer to back of heater unit using the supplied screws. Install the four screws by hand, finger tight.
12. Re-attached heater unit and tighten screws.
13. Re-attached sensor wires.
14. Tightened the four bearing retainer screws.
15. Attached new drum bearing to drum using the three supplied Torx screws. I used tape to hold everything together while installing the screws.
Tightened the Torxscrews.
Next I used a vacuum to remove all the lint from inside the dryer. I also used a small plastic putty knife to remove the caked on lint on the impeller blades.
16. Inserted drum bearing into bearing retainer.
17. Installed drum belt and belt tensioner.
18. Installed left side panel and feet.
19. Replaced the two grey and two white slide bearings on the front panel. They just slip onto a small post and slide into a slot.
20. Installed front panel. (Rotate drum to help with installation)
21. Installed top panel and door
PROBLEM SOLVED!
Other Parts Used:
-
Gene from Kutztown, PA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
86 of 132 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
squeaky dryer for a week or two
First I unplugged the dryer and turned off the gas
Second I opened the door and unscrewed the two screws that go up into the top panel and hold it in place (you will need to get down and look under the top of the door jam to see the screws).
Third I lifted the front of the top enough to remove the two screws holding the front panel on (Use a magnetic screwdriver if you have one you do not want to lose the screws taking them out or putting them back in)
Fourth positioned a chair to lean front panel against so it would not fall over or strain the electrical wires that run to the switch in the door (slide the front panel off slowly supporting the drum with your hand so it doe not drop hard on the motor wires or burners)
Sixth determined the parts I needed and ordered parts from pars select and got them in two days
Seventh when new parts arrived I unclipped the old DRUM BEARING removed the felt gasket, put the felt in the new Drum bearing and clipped it in place
Eighth clipped in the 2 new Dryer Drum Slides and 2new SLIDE WH slides
Ninth Vacuumed out dryer and vent pipe completely
Tenth reassembled dryer being careful to make sure drum was properly aligned as I put the front panel in place and the belt was in the proper place on drum and all the screws were back in place.
Ninth turned gas back on and plugged in dryer
Ten turned on dryer to test squeak was gone
Hints as soon as you hear a squeak look into it and you will probably not have to replace the DRUM BEARING. But if any of the Slides are bad replace them all. Check your belt and felt gaskets to see if they are in good shape. If everything up front is in good shape and it is not the motor squeaking it could be the back drum bearing. Take your time keep your old dryer running for a few more years and save the $40 dollar service call. Do not forget to clean out all the old lint and dust out of your dryer and vent pipes not only will you reduce the risk of fire you will be allowing air to pass through the dryer more easily drying your clothes in shorter time.
Second I opened the door and unscrewed the two screws that go up into the top panel and hold it in place (you will need to get down and look under the top of the door jam to see the screws).
Third I lifted the front of the top enough to remove the two screws holding the front panel on (Use a magnetic screwdriver if you have one you do not want to lose the screws taking them out or putting them back in)
Fourth positioned a chair to lean front panel against so it would not fall over or strain the electrical wires that run to the switch in the door (slide the front panel off slowly supporting the drum with your hand so it doe not drop hard on the motor wires or burners)
Sixth determined the parts I needed and ordered parts from pars select and got them in two days
Seventh when new parts arrived I unclipped the old DRUM BEARING removed the felt gasket, put the felt in the new Drum bearing and clipped it in place
Eighth clipped in the 2 new Dryer Drum Slides and 2new SLIDE WH slides
Ninth Vacuumed out dryer and vent pipe completely
Tenth reassembled dryer being careful to make sure drum was properly aligned as I put the front panel in place and the belt was in the proper place on drum and all the screws were back in place.
Ninth turned gas back on and plugged in dryer
Ten turned on dryer to test squeak was gone
Hints as soon as you hear a squeak look into it and you will probably not have to replace the DRUM BEARING. But if any of the Slides are bad replace them all. Check your belt and felt gaskets to see if they are in good shape. If everything up front is in good shape and it is not the motor squeaking it could be the back drum bearing. Take your time keep your old dryer running for a few more years and save the $40 dollar service call. Do not forget to clean out all the old lint and dust out of your dryer and vent pipes not only will you reduce the risk of fire you will be allowing air to pass through the dryer more easily drying your clothes in shorter time.
Other Parts Used:
-
warren from Flint, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
63 of 70 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy and took too long to dry clothes
Easy repair. Removed top of dryer and removed two screws to front panel and door assembly. Old front air duct assembly was worn and broken, so it literally fell off the panel. I cleaned the front panel and door assembly of all the lint and dirt, and snapped the new parts into place. The new parts came with the gasket and felt drum seal already installed, to all that had to be done was to snap it into place. Installing the drum slides was a breeze. I simply had to slide one end in the slot, position the hole over the pin, and slide the other end in. I put everything back together, and ran a full cycle for test. Dryer works like new, and run quiet.
Other Parts Used:
-
Bruno from Somerdale, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
56 of 68 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- 2
- 3
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- 2
- 3
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brent
July 20, 2017
I’m changing all the bearing slides on my dryer how many do I need and why are they different colors?
Hi Brent, the bearing slides are different colors to tell the difference between them. If you are replacing the front bearing slides in your dryer you will need 2 lower slides WE1M504, which are white. You will also need two upper slides WE1M1067, which are green. Good luck with this repair.
84 people found this helpful.
Was this helpful?
Thank you for voting!
Glenn
October 2, 2017
Do I need 2 white slides and 2 Green slides for this dryer? If so do the slides come as a set or are they single? In other words when I order the white slide is it a set of 2 or just a single slide?
For model number DHDSR48EF2WW
Hi Glenn. You will need to order 2 of the white slides and 2 of the green slides. They are sold individually . Hope this helps!
42 people found this helpful.
Was this helpful?
Thank you for voting!
Nina
July 20, 2017
My dryer is making a terribly loud noise when I first turn it on. Is there a kit or something I should get for it? Ive been looking at your parts list and if I change the top drum bearing I think I will need the drum slide bearings. How many do I need and which ones should I order??? Are there any other parts I should order to stop the noise? Thanks for the help!
Hi Nina, great question. Changing your front bearings would be your first step as worn ones can cause loud noises throughout the drying cycle. To change the upper bearings, you will need 2 of WE1M504 and 2 of WE1M1067. If you decide to also change the rear bearing which would be the second most common cause for the noise, the part would be WE25M40. Let us know if you have any further questions.
21 people found this helpful.
Was this helpful?
Thank you for voting!
Bobby
August 13, 2017
While drying it is making a squeaking noise that is coming and going like it maybe the belt squeaking
For model number DBXR463GD1WW
Hi Bobby,
Thank you for your inquiry. Your belt could be the issue. If it has worn down so much that maybe it is slipping against the pulley. However it is more likely that you will have to replace either your bearing slides or your pulley. I would check all of these parts to see which one of them are causing your problem. They are all physical parts, so when you look at them you should be able to determine which one is causing the problem for you. The belt and the slides would be parts that get worn down, the pulley is just something that you turn the wheel on and you will hear if it is making the squeaking noise. Good luck with your repair.
19 people found this helpful.
Was this helpful?
Thank you for voting!
Calista
July 20, 2017
I bought and am currently replacing the rear bearings. Since the dryer is already pulled apart how can I tell if I should replace the front bearings or the support?
Hello Calista, thanks for getting in touch. You will know to replace the front bearings or the support if you see any visible damage. Wear is normal, but if the parts are damaged in any way they should be replaced. I hope this helps!
10 people found this helpful.
Was this helpful?
Thank you for voting!
Jim
December 2, 2017
The dryer is not drying loads in normal time. It is also making a noise as if something is flopping around inside as the drum turns. There is nothing in the dryer and it still makes the noise. What should I check and in what order.Thanks, Jim
For model number DBXR453ET5WW
Hi Jim, Thank you for the question. You can check the belt to make sure it is not wore out and and preventing the drum to turn as it should.You can also check the Rear Drum Bearing for wear. Make sure the appliance is getting proper air flow. Clean the Lint Trap Duct Assembly and the Air Vents. You can use a Multi Meter to test the High Limit Thermostat and the Bias Thermostat as well for proper continuity. Hope this helps!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Juan
March 14, 2018
A question about dryer . Once in awhile durnh a drying cycle the dryer will make a squeaking noise.And sometimes the dryer will take a long time to dry but i found the front seal was broken and not fully there.
Hi Juan,
Thank you for your question. The squeaking noise you are hearing is likely a worn drum support roller that needs to be replaced. It is always recommended to replace both of them at the same time. If your dryer is taking a long time to dry and the front seal I would recommend replacing it as this is likely causing the issue. I hope this helps. Thank you and have a great day!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Hansel
April 10, 2018
How many glide slips would come with this? The dryer needs four. Does this purchase buy me four?
Hi Hansel,
Thank you for your question. These parts are sold individually. Be sure to check your model number and make sure that you need four of these ones and not two of these slides and two of a different kind. Good luck with your repair.
6 people found this helpful.
Was this helpful?
Thank you for voting!
Michael
January 31, 2018
I ordered replacement slides and got 4 white slides. Can I use these or is there a specific reason for the Green slides?
For model number DBVH512EF0WW
Hi Michael, Thank you for the question. The appliance needs 2 of the white and 2 of the green in order to operate properly. Hope this helps!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Denny
October 29, 2017
My dryer makes a thumping noise when it is running.
For model number GFDN120ED1WW
Hi Denny,
Thank you for your inquiry. There are some parts that you will need to check to see which one is causing the issue. You will need to check the drive belt, the idler pulley wheel, the complete duct trap assembly, the idler arm, the bearing retainer and the bearing slides. I hope this helps. Thank you and have a great day!
6 people found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- 2
- 3
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS755842
Manufacturer Part Number: WE1M504
Manufacturer Part Number: WE1M504
Brand
Model Number
Description
![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)