The water inlet valve in your washer connects to the water source and solenoid wires, and ensures the tub has the right amount of water entering it. If your washing machine continues to fill after it is full, or if it fills slowly, you may need to replace this valve. Before you begin this repair, be sure to disconnect the water and power sources from your washer. This part is sold individually.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your LG Washer Inlet Valve Assembly
Troubleshooting
This part fixes the following symptoms:
Water Filling Issues | Leaking
This part works with the following products:
Washer.
This part works with the following products:
LG, Kenmore.
Part# 5220FR2008F replaces these:
AP4445613, 5220FR2008F, 5221ER1002B
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
5.0
Filter By Rating:
5 Stars
3
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Glen S - March 24, 2023
Verified Purchase
It doesn’t leak
As you may know the first valve I was sent leaked, your service representative, I’ve forgotten her name , got another one ordered for me which I received the next day , super delivery, it works just fine , and you refunded the first one that leaked . This is the set time I’ve ordered from you . Excellent service and delivery, thanks very much . ??
★★★★★
★★★★★
Alain D - March 24, 2023
Verified Purchase
A++ Product
Recommend to purchase if any failure for this inlet valve, smooth no noise when running, wouldn’t buy any other valve. A++
★★★★★
★★★★★
Cameron A - August 10, 2023
Verified Purchase
The right part fast
The valve I ordered was here faster than I thought it would be. Less than 48 hours. Functions perfectly.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.2 / 5.0, 8 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
dispenser would not stop filling with water
replaced the cold water valve inlet
Other Parts Used:
Debra from Reseda, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
54 of 92 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water continued to fill into the drum slowly after the load was done.
Watched a you tube video and followed the instructions. Even had my 11 and 13 yo old help and do most of the work. Very easy to fix both hot and cold inlet at the same time. Didn't know which one was causing the problem so I decided to replace both.
Water was building up inside drum while machine was off.
I unplugged the washer shut off the water and disconnected the hoses. Then removed the top lid and removed old valves and installed new ones. Very easy plug and play installation.
Water was slowly filling up in washer tub, after I would wash clothes 2 or 3 days later there would be water standing in the washing machine.
I looked this problem up on YouTube like I do with everything, I saw a video from this site.. so I ordered what I needed from the website. The parts came in I unpluged the washer from the wall very important, I literally removed 6 Philips head screws and unclipped the wires from the parts and removed the hoses with the pliers, hoses have squeeze clamps. Put in New parts put hoses back on wiring back on and I was done.. it took me a total of maybe 10 minutes.. NO MORE WATER standing in the washer.. Thank you!! I would recommend you add a video for the Inlet Valve Assembly like you have for the hot inlet valve though...
Unplugged washer. Disconnected water line, Removed 2 screws then removed clips for hoses on inlet valve. Replaced valve and hooked hises back up. Replaced plate or rear of washer and plugged back in. Works great and even with cost of 1 day delivery, saved at least $200 doing myself.
Other Parts Used:
Janice from OVIEDO, FL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Wrench (Adjustable)
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water continued to flow into machine during drying cycle and afterwards
This was a very easy repair. Just followed the steps in the videos on the website (I replaced both the hot and cold inlet valves, so two different videos, but the process for each is similar) and it couldn't have been simpler.
Water would fill the basin when the washer wasn't used. I followed the video created by this site to make the repair. The video gave me the confidence that I could successfully make the repair myself. The hardest part was physically moving my washer out of its corner to make the repair. The parts were plug and play. Awesome!!
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
8 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Letellier
November 29, 2017
My washer keeps filling with cold water even when unplugged. A local store tested the 4 inlet valves and they would all open/close properly when given current. What can the problem be?
For model number mw1832cw
Hi Letellier,
Thank you for your question. The Water Inlet Valve on your washing machine is used to fill the tub with cold, warm or hot water for the wash and rinse cycles. The valve is operated by electric solenoids that are controlled by the timer or electronic control board and the water level control/water level selector switch or pressure switch. If your washer continues to fill during a cycle, the water inlet valve could be at fault. To verify that the valve is at fault, unplug the washer when the symptom occurs. If the washer continues to fill, then the water inlet valve is defective. If the washer stops filling, then the problem is related to the electrical circuit that controls the valve. Also, The water level switch is a pressure activated switch that is used to determine the correct water level in the tub. This part is normally located behind the control panel and will have a hose or air dome tube that connects it to the tub. On washers that use an electronic control, this switch may be located at the sump area below the tub. As the water fills in the tub it will compress the air in the tube and push against a diaphragm inside the switch. The switch will control the water inlet valve and turn the valve off at the correct water level. If the tube has a leak or is plugged, not enough pressure may be created to activate the switch and the washer may overfill. If the switch is defective it may also cause the machine to overfill. I hope this helps. Thank you and have a great day!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Joe
October 6, 2017
While my washer is off ,it still can fill up with a couple of gallons of water over night. We came back from vacation after a week . And it was up to the door.
For model number Wm2487H*M
Hi Joe. Thank you for the question. It sounds like the water inlet valve is "stuck" open and letting water into the tub while not in use. To fix this issue you will need to replace the Water Valve. Hope this helps!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Carlo
November 19, 2017
How do i know to replace the water valve inlet or just the hot water valve inlet? One is $17-$25 the other is $65-$90.
For model number WM2487H*MA
Hi Carlo,
Thank you for your inquiry. To verify which water inlet valve is working correctly, you will need a multimeter to check the continuity of each part. I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Ricky
February 10, 2020
My washer seems to slowly fill days after use but not so bad that it overflows. Would the water inlet be the correct replacement?
For model number Lg steam washer WM2487HWMA
Hello and thank you for writing.
Yes, Ricky, this is usually an indication of a faulty water inlet valve. We hope this helps. Please contact us anytime if you require further assistance.
1 person found this helpful.
Was this helpful?
Thank you for voting!
CK
September 9, 2022
Is this cold water inlet valve compatible with my LG washer model?
For model number LG WM3360H*CA
Hi CK,
Thank you for your question. Yes, this would be the correct water inlet valve for your washer. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Patricia
February 26, 2023
Code FE is displayed. Which part needs to be replaced?
Thank you.
For model number WM2487H*MA
Hi Patricia, thank you for getting in touch. Based on our research, this error code means your LG washer is overfilled. The main cause of this problem is that your intake valves are faulty and not turning off when they should. To fix the problem, you will need to replace the intake valves, part number PS3527431. Before replacing the water inlet valve, you will need to check the continuity of the valve to make sure a continuous electronic path is present or not. We hope this helps, good luck with this repair!
Was this helpful?
Thank you for voting!
Kimberly
April 4, 2023
My drum very slowly fills up with water when the washer is off and the bleach tray never seems to drain. Would replacing the water inlet valve fix both issues?
For model number WM2450HRA
Hello Kimberly, thank you for the question. Based on our understanding of the issue, we would suggest you replace the water inlet valve, part number PS3527431, to resolve the problem. We hope this helps, good luck with this repair!
Was this helpful?
Thank you for voting!
Steve
September 5, 2023
Leaking water in the drum. Do you change both valves? Are they the same part number?
For model number LG WM2487HWMA
Hi Steve, thank you for reaching out. According to our research, there are two inlet valves in your model. The water inlet valve, part number PS3527431, and the hot water inlet valve, part number PS3527427. Check both valves and replace the faulty one. We hope this helps!
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Affresh® Dishwasher Cleaner is the #1 recommended cleaner by Whirlpool, KitchenAid, and Maytag brands, designed to remove limescale and mineral build-up that can affect your dishwasher’s performance. These powerful table...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS3527431
Manufacturer Part Number: 5220FR2008F
