We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
9 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sunil
November 28, 2018
My oven does not heat up. Stays on 100f. I took the high range thermostat (318578506) out and tested its resistance and got 0.3 something ohms. So figured it was good. After i put it back the oven works. Then weeks later the same issue. I removed the thermostat again and put it back and it works again. Any ideas?
For model number FFEC3024LB
Hello Sunil, Thank you for the question. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Paula
January 2, 2018
Is there a thermal circuit for this oven, fuse or a switch? After self cleaning my oven won’t heat past 100 degrees.
For model number EW30EW65PSB
Hi Paula,
Thank you for your question. There is no separate fuse from what I am seeing underneath your model information. I would suggest checking your elements, and your temperature sensor inside of your oven with a multi meter. The elements should read anywhere between 0 - 50 ohms of resistance and the temperature probe should read anywhere between 1000 - 1100 ohms. If all three of those parts are working inside of your oven, then you may want to check the control boards on your appliance. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Barbara Perreault
November 6, 2018
I replaced the temp sensor it didn't need to be thought that was the problem but the temperature does not stay hot i do pre heat i got to bake and then the temp takes a while to get there and when it does the tempurature drops and doesn't cook it just drops down what is wrong and what part do i need to replace the tempurature control itself not the sensor ??
For model number FPES3085KFF
Hello Barbara, thank you for your question. If the sensor was replaced and didn't fix the issue the control board should be replaced. That is part number Electronic Control Board Part Number: PS2368654.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Ed
March 1, 2019
The cool down fan continues to run, has been running all night, what needs to be done?
For model number oven model 790.48783901
Hi Ed,
Thank you for your question. The cool down fan will run until the area around the microwave has cooled. Units over a range or oven may automatically turn on the exhaust system when the area around the microwave becomes too hot. The exhaust system cannot be shut down until the temperature returns to a safe level. If it is not turning off and the area around the microwave is cool, then you will need to check the thermostat, the control board and the door switches to see if they are causing this issue. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jean-Marc
January 25, 2022
Does that piece will fix the problem of a cooling fan who never stop? Thanks
For model number CGES3065KF6
Hello Jean-Marc, Thank you for the question. Normally this would indicate the Thermostat is faulty. it can also be tested. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. We hope this helps!
Was this helpful?
Thank you for voting!
Serge
April 8, 2022
Hi, I have a « clunking » sound like the one I hear when turning on my stove, it is the coolong fan starting. But to hear this sound even when I am not using the stove is not normal, could this be a faulty cooling fan, relay, cooling fan thermostat???? Thanks for helping me pinpoint the problem.
For model number CGES3065KF5
Hi Serge,
Thank you for your question. If the oven was recently used and you are still hearing the cooling fan, this is normal. The fan will stay on until the oven has cooled. If it is coming on by itself, then a relay for either the bake or the broil element has shorted out on the electronic control board or the contacts on the oven cooling fan thermostat are stuck closed. You will need to check these parts to see which one is causing the issue. Once you have determined the part you need, please feel free to call customer service. We are open 7 days a week and anyone will be happy to assist you. We look forward to hearing from you!
The top oven of my double wall oven setup isn't working properly (its not maintaining temp), the first thing i thought it was the thermostat to which i realized what i was looking at was the temperature sensor. I recently replaced the temp sensor and the top over is still not heating up, i set both ovens to the same temp at the same time and when i checked on after 20min bottom was around 280 while the top is around 147. What i did notice is that the exhaust fan for the top oven was blowing real hard as if its cooling down the oven when it should be heating up. The question is would replacing the actual thermostat fix this issue? In the diagram i am seeing only seeing 1 thermostat, is only one needed to control both ovens or 1 for each? If its not the thermostat would it be the chip board, whats throwing me off if its only 1 thermostat controlling 2 ovens wouldn't both ovens not heat properly? Thanks
For model number FFET3025PSD
Hello Warren,
Thank you for your question. If you already replaced the temperature sensor for the upper oven, then it is likely that it is a faulty control board and the control board would need to be replaced, yours is under part PS1528196 for your model. Hope this helps!
I set oven at 350 and it comes up to temp. Display stays at 350 but temp drops. I hit "convection" enter "350" and it shows oven temp as low as 250. I push start and it comes up to temp only to fall again.
For model number FGET3065PFC
Hello Lance and thank you for writing.
It certainly sounds like a faulty temperature sensor PS1175815 and/or bake element PS3655318you should check for signs of damage, and replace it if needed. We hope this helps. Please contact us anytime.
Hi. My frigidair stove is showing error code f30. The probe, wiring and control panel checks out good. Will the high limit switch produce this code. Thanks
For model number fridigdair stove CGDS3065KF7
Hello and thank you for writing.
The F30 and F31 codes differ slightly, even though they both indicate a problem with the oven temperature sensor. Specifically, the F30 code indicates the probe could be broken or unplugged or its wires could be broken or damaged. In rare cases the high limit thermostat can cause this, more likely is a faulty main terminal block PS471605 or the wiring connected to it. We hope this helps. Please contact us anytime if you require further assistance.
Average Repair Rating: 3.8 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Thermostat for oven cook elements. Cooling fan is a misnomer-the fan still worked!
First of all I am not Betty, I am her husband. Second I and a friend pulled the range out of the countertop (which was not necessary). The top can be raised on it hinges and the plate under the burners can be removed by taking out 8 to 19 screws and there is the thermostat looking at you. After doing this once and knowing where the thermostat is, the job could be done in less that an hour.. INSTRUCTIONS: Turn OFF the circuit breaker. Remove the burners. Remove the plate under the burners. Change the thermostat (making sure to place in correct direction as the one removed). Reassemble, turn on circuit breaker, test oven heat.
Other Parts Used:
Betty from OLIVE BRANCH, MS
Difficulty Level:
Very Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
4 Reviews
5.0
Filter By Rating:
5 Stars
4
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Dave W - December 21, 2022
Verified Purchase
Easy repair
The part seems to have fixed the issue i was having...oven has not overheated since the part was installed
★★★★★
★★★★★
Shari J - December 11, 2021
Verified Purchase
My stove works again! Yay!!
The part was in good condition and came fast. So thankful to have my stove working again before Christmas ??
★★★★★
★★★★★
David T - November 17, 2021
Verified Purchase
parts
thanks works great fast order
★★★★★
★★★★★
Dmytro G - January 24, 2021
Verified Purchase
Easy repair
Good timing. Part works fine. Thank you
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS3409411
Manufacturer Part Number: 318578506
