Part Location Diagram of WR17X4310 GE Ice Bucket and Auger Assembly
See part 352 in the diagram
Replacing your General Electric Refrigerator Ice Bucket and Auger Assembly
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Ice Bucket and Auger Assembly

$410.91
  Special Order
PartSelect Number PS294037
Manufacturer Part Number WR17X4310
Manufactured by GE
Part Videos

Replacing your General Electric Refrigerator Ice Bucket and Auger Assembly

Replacing your General Electric Refrigerator Ice Bucket and Auger Assembly
Troubleshooting
This part fixes the following symptoms:
Ice maker won’t dispense ice
This part works with the following products:
Refrigerator.
This part works with the following products:
General Electric, Kenmore, Hotpoint.
Part# WR17X4310 replaces these:
AP2066342, 295407, WR17X4310, WR17X2082, WR17X2775, WR17X2899, WR17X3730
Back to Top
Customer Repair Stories
 Average Repair Rating: 4.6 / 5.0, 8 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Ice make auger rusted, unable to serve clean ice.
Replacement auger and ice bucket assembly was perfect. Just had to remove the front door/flap assembly from the old unit and screw on to the new. The water filter kit took more time to read the box instructions than it did to install. Perfect. Am very pleased with the service/value offered by PartSelect.
Other Parts Used:
In-Line Water Filter
  • Frank from Las Cruces, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
49 of 64 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace icemaker
I slid the old ice maker (which was rusty) out of the freezer. I emptied the ice cubes. I unscrewed the 3 screws holding the plate to the old ice maker. I attached the original plate to the new ice maker/ auger unit with 2 screws. The new icemaker assembly did not match up with a 3rd screw hole. The 2 screws seem to be holding securely.
I reinserted the new assembly. Shorly after this nice clean ice cubes began to form. Works very well!
Other Parts Used:
  • Conrad from Oglesby, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
12 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rusty auger and crusher broke
as simple as taking off 4 screws from door of old one and putting door on new one and putting bucket back in place
Other Parts Used:
  • david from frankston, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The original ice auger jammed and destroyed the original icemaker
The replacement part was an exact fit and slipped right into the space where the old one was. No tools needed.
Other Parts Used:
  • James from Lafayette, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Auger in the Ice became Rusty
Once I received the New part, I simply removed the old one, unscrew the door assembly off of the old one and reinstall it on the new one using only 4 screws. Then simply pluged in the New Ice Bucket. If it were any easier, My Kids would have done it.
Other Parts Used:
  • William from Miami, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Part of my ice bucket assembly had broken off
All I did was take the old bucket out,, which had been frozen to the base, and I had to thaw out, by turning the refrigarater off , and use a hair dryer to melt the ice, after that I unscreewed the outer face of the old bucket, and replsced it to the new bucket
Other Parts Used:
  • Wallace from Detroit, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The auger and ice bucket assembly was worn out and rusty
I simply removed the screws holding the plastic face plate to the old auger/ice bucket and attached it to the new one. It was a simple procedure
Other Parts Used:
  • Philip from Sterling, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The feeder was rusted and would get all over the ice
Opened the box, removed the ice maker, removed the old ice maker from freezer, empty drawer of ice into the sink( the hardest part of the job) Phillips screw driver and removed the four screws holding the plastic front on and installed it on the new ice maker. Put it in freezer and I am back in business . This is real easy
Other Parts Used:
  • David from WINDHAM, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

1 question answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Joseph
January 10, 2020
Does this part include an ice crusher?Ice bucket and auger assembly (bracket auger) part number ps294037
For model number 36358067891
PartSelect logo
Good Day Joseph. Thank you for your question in regards to your unit (Model Number 36358067891). Based on our research, we can confirm that the Ice Bucket and Auger Assembly (PartSelect Number PS294037) would include the ice crusher. You can order this part either online at our website www.PartSelect.com or by calling us by phone at 888-260-4310. Best Regards.

Was this helpful?
Thank you for voting!
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS294037
Manufacturer Part Number: WR17X4310
Brand
Model Number
Description
Kenmore
36350221000
Refrigerator
Kenmore
36350222000
Refrigerator
Kenmore
36350227000
Refrigerator
Kenmore
36350232000
Refrigerator
Kenmore
36350237000
Refrigerator
Kenmore
36350242000
Refrigerator
Kenmore
36350247000
Refrigerator
Kenmore
36358062890
Refrigerator
Kenmore
36358062891
Refrigerator
Kenmore
36358062892
Refrigerator
Kenmore
36358062893
Refrigerator
Kenmore
36358062894
Refrigerator
Kenmore
36358062896
Refrigerator
Kenmore
36358062897
Refrigerator
Kenmore
36358067890
Refrigerator
Kenmore
36358067891
Refrigerator
Kenmore
36358067892
Refrigerator
Kenmore
36358067893
Refrigerator
Kenmore
36358067894
Refrigerator
Kenmore
36358067897
Refrigerator
Kenmore
36358251890
Refrigerator
Kenmore
36358251891
Refrigerator
Kenmore
36358251892
Refrigerator
Kenmore
36358251893
Refrigerator
Kenmore
36358251894
Refrigerator
Kenmore
36358252890
Refrigerator
Kenmore
36358252891
Refrigerator
Kenmore
36358252892
Refrigerator
Kenmore
36358252893
Refrigerator
Kenmore
36358252894
Refrigerator
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service