Ask our experts a question about this part and we'll get back to you as soon as possible!
8 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Era Marshall
April 15, 2018
The water is leaking from part 71. How do you get it out and put it back? There is an electric wire attached to the bottom of the red stopper thing.
For model number fghd2433kkf1
Hi Era,
Thank you for your question. Before you begin any repair please unplug the appliance from the electrical outlet and turn off the dishwasher's water supply. The turbidity sensor is mounted on the sump and tells the control board how dirty the water is so it can adjust the cycles. You will need to pull the dishwasher out to do the repair. You will need to disconnect the lines. First you will need to remove the dishwasher drain line. Have towel handy in case any water comes out. You will also need to remove the fill line attached to the hot water tap. Once you have this done, you can open the dishwasher door and take the bottom rack out. Then remove the screws that the dishwasher to the countertop. Once the screws are removed, You can pull the dishwasher out of the cabinet and lay it down on its back. Be sure to lay a blanket or towel down before you lay it down in case any water comes out of the dishwasher. Once the dishwasher is on it's back, you will now have access to the bottom of the dishwasher and the turbidity sensor. It is mounted on the sump just under the drain pump. Remove the wiring harness attached to the sensor by pressing on the locking tab to release it. To get the sensor out of the sump you will need to turn it counter-clockwise and then pull it out. To install the new sensor and reinstall the dishwasher under the counter follow the steps in reverse and once the dishwasher has been reinstalled turn the water back on and plug the power back in and the dishwasher should work now for you. I hope this helps. Thank you and have a great day!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Kevin
February 18, 2020
My dishwasher keeps setting itself to 99+ minutes even on quick wash cycle. I'm guessing its the turbidity sensor. Is there any way to test this?
For model number FPHD2481KF1
Hello, Thank you for your question. You can test the turbidity sensor, this link shows resistance and specs- http://www.mouser.com/catalog/specsheets/920-480A_E_LR.pdf . You may also need to check your control board, if the timer is messed up it will not allow it to run properly. We hope this helps, good luck with this repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Steve
October 29, 2017
Turbidity sensor is held in by what , we have developed a leak and are using a zip tie .
For model number FPHD2481KF1
Hi Steve, Thank you for the question. On the side of the sensor there are tabs that stick out and the sensor will just push up into place and lock in with these tabs. Good luck with the repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Whitney
November 15, 2017
I need the rubber seal that goes on the part 71 underneath the dishwasher.
Hi Whitney,
Thank you for your inquiry. Before we can assist you further we would need the model number from your appliance. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Sarah
January 21, 2018
My dishwasher works but when it get to rince cycle. It dont stop. Just keep doing it. Washing drying er clean s. What is wrong plz help
For model number Fghd2465nf1a
Hi Sarah,
Thank you for your question. If the dishwasher will not stop running there are some parts that you will need to check to see which ones are causing the issue. You will need to check the touchpad and the electronic control board, the motor, the heating element, the thermostat and the fill valve. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Christopher
May 4, 2023
will you just sell gasket to part # AP4432768
Hi Christopher,
Thank you for your question. The gasket is sold with the turbidity sensor. We hope this helps!
Was this helpful?
Thank you for voting!
CHAD
June 26, 2023
My frigidaire dishwasher stopped heating. I changed the heating coil and thermostate. That didnt work. What to check next?
For model number FFID2426TSOA
Hi Chad, thank you for contacting us. Since you have replaced the element and the thermostat and that did not fix the issue, we would recommend replacing the control board, part number PS12114591, to solve the problem. It manages the functions of the dishwasher such as washing, draining, and drying. Glad to be of help!
Hello, my dishwasher suddenly didnt drain the water anymore. So I have removed the drain motor pump and check it with a multimeter and value was moving all the time with high and low value, so I have replaced it by a new one and test it before installing it and every thing was fine (a fix value around 240ohm). I tryed a new cycle and the problem is still there the dishwasher doesnt want to drain. Do you think it could come from the turbidity sensor, or any other piece ?
Thank you for your help
For model number FGBD2434PF0A
Hello Remi, thank you for reaching out. Based on our understanding of the issue, we would suggest checking the drain hose and pump filter. If they are not clogged, then you may need to replace the control board, part number PS8689436, to fix the issue. We hope this helps.
