Average Repair Rating: 2.8 / 5.0, 3 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Leak in the hose that feeds the upper wash arm
First I disconnected the dishwasher electric, water supply and discharge hoses. I then pulled the dishwasher out. After opening the door, I removed the retainer clip holding the upper wash arm, then the nut holding the top shower hose in place. Close the door and lean the dishwasher on its side to get at the underside where the other end of the hose is. Loosen the hose clamp and remove the top shower hose. Reassemble everything in reverse order. In hindsight, I didn't need to buy the new hose clamp or the tub top washer (I reused the originals). Good luck!
The problem was the rubber end on the upper shower head pipe at the pump. Not to hard . Slide dishwaser half way ouy the ptpe is on the right side.The bottom end is is just a clamp the top drops in from the top, inside there is a nut above the upper shower head. You can unsrew the nut with your fingers, it is right above the upper shower head.There it a washer at the top of the pipe that should be replaced that doesnot come with the pipe
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leak in top shower hose
Hardest part is removing unit from under counter. Degree of difficulty will depend on how plumbing and electric are connected to unit. In my case the supply hose, electrrical cable and waste hose all had plenty of slack and unit only has to come out about 20" to get to top tub connection.
The leak was on the rubber connection that attaches the hard plastic hose to the pump under the tub. That attaches with a standard automotive type screw band clamp. The other end goes into the top of the drum and atttached into the uppper spray arm with a plastic nut (I replaced the rubber washer when changing this side just to be safe.)
Level of difficulty for me was easy but if you are not familiar with dishwasher installation and connections, could be time consuming. And obviously had to discern where leak was before ordering parts. I had taped it with black electrical tape as a temporary fix to make sure that was the part that was leaking. It was not obvious as it was just a small pinhole.
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Terrence
April 25, 2018
There appears to be a gasket under the spray arm that has come apart. I found a small screw that was laying under the spray arm mount as well. I've taken the spray arm apart several times to clean it. Today I noticed the decaying state of the gasket when I cleaned it. Is there a part to replace this? Tks
For model number MDB4100AWW
Hello Terrence, Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is PartSelect Number: PS11747620. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Terrence
April 25, 2018
The problem doesn't seem to be a hose leak, although the tiny screw may have held a hose in place. The decayed gasket is underneath the round base that holds the spray arm, spray arm mount. I fear the gasket is causing a leak that i haven't detected yet. I couldn't tell from your recommendation if the part was a gasket or a hose. Tks tw
For model number MDB4000AWW
Hi Terrence, Thank you for the question. I suggest replacing the gasket since there is wear. Even if it is not causing the leak, it may cause issues soon.Hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2097450
Manufacturer Part Number: 910069