On a washer, this part is used for circulating the water. On a dishwasher, it is used for draining the water.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will not drain | Not draining | Noisy | Leaking
This part works with the following products:
Dishwasher, Washer.
This part works with the following products:
LG, Kenmore.
Part# EAU61383518 replaces these:
4681EA2002D, 4681EA2002H
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 2 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Drain pump needed to be replaced
Replaced drain pump following easy to follow video. Also replaced circulation pump at same time, as it is connected to common sump housing and only added a few more minutes to repairs.
Disconnect washer - pull out and turn on it's right side. Remove bottom plate (2 screws). Water intake valve is attached to water line. Disconnect water line. On the other end of the pump is a rubber hose. Disconnect hose by using a pair of pliers to open pipe clamp. Disconnect the electric line by pulling the pronged plug out of the pump. The part is composed of the pump and a metal mounting plate. They are connected by 4 screws. Remove the screws and pull out the back half of the pump. The front of the pump is attached to the washer frame by 2 screws. When removed you will notice an o-ring that forms the seal between the two halves. Remember this when installing the new pump. You will have to take the new pump apart because the whole part will not fit through the frame opening, thus the need to make sure the o-ring is properly seated. You can either install the mounting plate to the frame then attach the pump half or with half of the part in front of the frame and the other half behind the frame connect the two, then attach it to the frame. Reconnect incoming water line using teflon tape and a crescent wrench. Reconnect out-flow line with the pipe clamp and attach the power line. Since you have to take the new pump apart make sure the o-ring is properly seated as it will have a tendency to fall out. Reassemble the rest.
Other Parts Used:
Gregory from DENVER, CO
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Susan
March 18, 2022
My dishwasher fills, drains and heats the water. However, it makes a strange noise and is not washing the dishes well. I wonder how to tell if it is a pump or an arm that doesn't rotate fast enough, or?
For model number LDF7932ST
Hello Susan, Thank you for the question. We suggest spinning the arm to see if it spins freely and check the holes to make sure there is no blockage. If the arm is good, you may have a faulty Circulation Motor Assembly. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
le code dishwasher fills with water then throws code if i restart it will drain water then refill and throw le code again
For model number ldf6810 st
Hello Thad, thank you for writing. The LE code could be the Impeller part PS3528695. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Tom
March 8, 2023
There are 2 motors one is solid while the other has a black cylinder. Solid white is located on the left as you face the clothes front loading washer. Which do I replace to resolve drain issue?
For model number Wm3001 hra
Hello Tom, thank you for contacting us. The part which you are looking for is the drain pump assembly, part number PS3579318. We hope this solves your problem!
The washer got a lot louder during the rinse and spin cycles. I took it apart and made sure none of the tubes were plugged.
When I checked the pumps, the one on the left as you're looking at the machine (K340), was full of water in the black casing behind the impeller. I'm guessing that the pumps are not supposed to have water down inside them?
For model number WM2501H*A
Hi Wayne, thank you for the great question. The drain pump does not have any water in it. it might be clogged or defective. Sometimes, small objects or articles of clothing can get caught in the drain pump. To determine if anything is blocking the pump, remove it and check for obstructions. If it is not blocked, then replace the drain pump, part number PS3579318. We hope this information helps!
The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle spee...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS16223509
Manufacturer Part Number: EAU61383518
