Water Actuator
Fits your 25357112604!
$207.72
In Stock
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Fits your 25357112604!
PartSelect Number
PS1526416
Manufacturer Part Number
241685701
Manufactured by
Frigidaire
Product Description
Water Actuator Specifications
Once a glass is pressed against the actuator pad it will cause the dispenser to deliver water when activated.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Not dispensing water
This part works with the following products:
Refrigerator.
This part works with the following products:
Frigidaire, Kenmore.
Part# 241685701 replaces these:
AP3967845, 1196680, 5304433615
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 2 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Broken Water Actuator Paddle
You pull out the tray at the bottom of the space in the freezer door where the ice and water are dispensed. The tray didn't come out easily, but don't be afraid of breaking anything. It is a simple interference fit. Then remove the two phillips screws at the bottom of the face plate and lift it gently. It can dangle from it's electrical connector while you do the rest of the job. Remove three phillips screws that hold the rest of the assembly in place. No need to completely remove the assembly. Do not disconnect the water tube. Disconnect the power plug at the left so that you can pull it out a little farther and not have to worry about shorting anything. The water actuator is secured by two small plates with two phillips screws and there is a spring too. Remove the screws and plates. There is also an electrical connection. The wires were installed under a relay at the factory so I had to trace the wires, disconnect the plug, and then snip the wires to remove. It's crowded in there so you have to work it around to get the actuator out. Then replace it with the new actuator. Reconnect the electrical and make sure the spring is in place. Then just go backwards. Put the plates back on, reconnect the power plug, screw the assembly back in, put the face plate back on, and slide in the tray back in. You might want to test the water and ice after you reattach the assembly but before the face plate. I needed the hemostat when I dropped one of the screws into the assembly. Needle nose pliers would work just as well or just don't drop anything.
Other Parts Used:
-
David from Porter Ranch, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
41 of 47 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water actuator broke due to extreme pressure in trying to make water run quicker
Remove the housing holding the sensors and actuador. The white sensor tape came off the command console, however this was easily replaced by removing the console cover and inserted the tape back. At first the fridge console (lights) did not respond, removed the tape again and re-installed the right way. The most difficult part was trying to push the small hose to fit through the housing and stay in place. In the beginning water was coming out through several places, but removed the housing again, fudgec with the little hose until it fitted snuggly into water dispensing opening. Replaced housing again, screwed all little screws and repair work was complete. The most difficult part was getting a tool that would allow you to guide the hose. Used a fine small plyer to pull through.
Works perfectly now.
Works perfectly now.
Other Parts Used:
-
GLORIA from MIAMI, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
13 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David
May 27, 2019
The ice maker only crushes ice even though it is set to cubes. Why would this be happening? Thanks.
For model number 253.5629240P
Hello David, thank you for inquiring. First check for any blockage in the Ice Container with Auger Assembly, which is part PS1991431 for your model. If there is no blockage, then you may need to replace it or the Ice Solenoid part PS8691995. We hope this helps.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1526416
Manufacturer Part Number: 241685701
Manufacturer Part Number: 241685701
Brand
Model Number
Description