Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jerry
November 9, 2017
Where are the screws located to remove this part from the refrigerator door?
For model number PLHS69EGSS1
Hi Jerry,
Thank you for your question. Here is repair story from our website that refers to the ribbon cable. Unplugged refrigerator. Pull forward on tray at bottom of water & ice dispenser to remove it. Remove three screws. Push up and then pull out to remove black cover around dispensers. Be careful not to break ribbon cable. Pulled ribbon cable from green circuit card on the cover. Set the cover aside. Removed green circuit card from refigerator (six small screws). Had to unplug two wires to do this. Set this aside. Make sure you remember which connector each wire goes in for re-assembly. I ended up removing the entire assembly, it was easier to work on. There were a couple more screws to remove and then you can carefully pull the entire assembly down and toward you to remove it. This meant removing the water supply line from the dispenser. Pushed up on the water supply line with needle nose pliers to "unstick" it and make it easier to pull out. Used needle nose pliers to unplug wires from broken actuator from the circuit card. Make sure to unplug the correct one. Unscrewed the two screws that held the metal plates thet held the actuator in place. Cut the wires to make it easier to remove the broken actuator and pull the wires through Installed the new actuator and screws. Routed the wire through and plugged it in to the circuit card. Now the hardest part, and I would not have figured it out without a tip from this website. There was no slack in the water line and it was impossible to push the end of it back into the hole in the dispenser assembly. Open the refrigerator doors and remove the black cover at the bottom. The water line goes up through the freezer door from the bottom. It was easy to push an inch or two of slack up through the door. Then I could grab the water line and insert it in the hole in the dispenser. Re-connect the wires that were disconnected and replace the assembly in the freezer door. You can pull slack in the water supply line back down fr
2 people found this helpful.
Was this helpful?
Thank you for voting!
Mauro
September 26, 2019
I try to dispense ice in my glass but i have to press like 6 time or press hard so it dispense the ice. I would like to know is it the issue of the ice dispenser actuator. Thank you
Hi Mauro, we cannot say exactly, it could definitely be the ice dispenser actuator. It is also possible there is some kind of blockage or other faulty part causing the ice chute door to be harder to open. Thank you for your question and good luck with your repair!
Was this helpful?
Thank you for voting!
David
October 12, 2022
Do you have a repair video on how to replace the ice.despenser actuator
For model number Flsc23f6dsn
Hi David, thank you for reaching out. We have researched your model and attached a relevant video that might help you with the ice dispenser actuator. We hope this is what you were looking for.
Was this helpful?
Thank you for voting!
Brenda
December 30, 2022
Is the lever you push to dispense water or ice?
For model number Fsc23f7db3
Hello Brenda, thank you for your question. The Actuator PS1526393 you had chosen is for the Ice. The Actuator for the Water Dispenser is PS1526418. We hope this helps.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1526393
Manufacturer Part Number: 241682303