This part is located in the water pump area of the ice cube maker.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Ice Maker.
This part works with the following products:
KitchenAid, Whirlpool, Kenmore, Jenn-Air.
Part# WPW10548509 replaces these:
AP6022829, 2313643, W10548509
Customer Repair Stories
Average Repair Rating: 2.6 / 5.0, 4 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Ice maker would not make ice. I went through diagnostics and it showed the level sensor was not working. Water would continue filling the reservoir and not shut off to start making ice.
Took off several plastic covers to gain better accessibility to the sensor. Had to pull out the whole support piece to get at the part. Took out the old sensor, cleaned the unit as best as possible, then installed the replacement. Turned on the power to the unit and reinstalled all the parts I took out for better viewing and accessibility. Started up the unit and it is slowly building ice, which I will remove and dispose of to start getting clean ice.
Other Parts Used:
William from LANDRUM, SC
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
8 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
only a partial refill of water bucket (would then run dry and make pump noise)
my sensor was stuck because of age, so I had to remove the water bucket to pry it out. It is easy to see what you have to remove to get to it. I used the mirror and rachet, extensions, 1/4 socket to remove screws. Tips - Remove the plastic door-inner to help working inside the bin. Also plug the drain because you will drop screws. Magnet sockets don't work on stainless steel. Later I found it is much easier to work inside the bin by pulling the entire unit out (shut off water and power, remove lower panel and disconnect drain tube). It sounds hard, but actually is easy. REMOVE THE TOP (4 screws). it stays connected because of wiring, but it allows full access and makes all kinds of repairs easy, especially pump replacement and even the circuit board behind the front panel buttons if you ever get to that point.
BTW Partselect is awesome, I have used a number of times for ice maker and dishwasher. My next project is the washing machine! Always the right part shipped very quickly.
Other Parts Used:
Thomas from HEBER SPRINGS, AR
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Sensor quit working
Removed and replaced sensor
Other Parts Used:
Floyd from VIAN, OK
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One of the circulation pumps was going bad and making a loud noise.
I replaced the two pumps, since both were the same design...figuring if one went bad then the other would soon go bad...and then I also replace the water level sensor. All had quick connect plugs. The time is just taking apart the various pieces, cleaning, installing the new pumps and sensor, then reassembling.
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bryan
December 29, 2017
How do you remove this part? It does not simply lift out.
For model number KUIS15NRTB2
Hello Bryan,
Thanks for your question. This part is located in the water pump area of the ice cube maker. You will need a 1/4" nut driver to remove it, and you may need to remove the metal bracket holding in the wire harness.
I hope this helps.
6 people found this helpful.
Was this helpful?
Thank you for voting!
Phillip
February 12, 2018
If this can be tested how would you do it?
For model number GI15NDXXQ1
Hi Phillip,
Thank you for your question. The sensor can be tested with an multimeter. Before testing the sensor with a multimeter, let it warm up to room temperature. It should read 6.2K Ohms at room temperature. If the readings are far off from what you are getting, then the sensor needs to be replaced. I hope this helps. Thank you and have a great day!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Thomas
April 2, 2018
You said to read 6.2k ohms, i am reading 10.2k ohms. Is this 10.2k ohms an indication of a faulty sensor. Thanks
For model number W10548509
Hello Thomas, thank you for your question. It should read 6.2K Ohms at room temperature. If the readings are far off from what you are getting, then the sensor needs to be replaced. Since your reading is 10.2k Ohms, I would say the sensor is faulty and needs to be replaced. I hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Jim R. Reid
February 26, 2019
Solinoid won’t shut off. Runs continually. Overfills resivoir. Drain pumps kicks on and drains excess water. Cycle repeats continuously without shutting off. Unit is fairly dirty from mineral build-up. Thank you for taking time for help.
For model number 106.89589702.
Hello Jim, Thank you for contacting us. I suggest checking the following part: PS1484571 Water Pump Assembly. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Our scratch-free, streak-free formula removes fingerprints, smudges, grease, dirt and oil, while protecting and polishing to repel dust and dirt. Use on all stainless steel appliance brands and surfaces. Stainless Steel ...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11756166
Manufacturer Part Number: WPW10548509