Igniter - Horizontal Mount

1st I opened door to stove and removed the wire racks. Then removed lower panel to get to igniter. Then I had to slide stove away from wall. Remove panel on back for accesss to wires. The new part had a plastic connector and the original just used wire nuts for the connection. So I cut off connector and stripped 1/2 inch of the end. Removed wire nuts from old igniter. Back into the oven removed 2 screws pulled out old igniter. Installed new igniter with 2 screws stuck wires through small hole to rear. Back around to back of stove. Connected wires with wire nuts.(I did not see any differnce in wires and dont think it matters) put everything back together and fires that baby up. I am gonna say 15-30 min job

Unplug oven. Remove oven door. Two latches on hinges must be rotated towards the door to release and then remove. Remove two thumb screws that hold drip pan in place and remove from oven. The ignitor is then exposed. Remove the two screws that hold the ignitor onto the burner asymbley. Pull wires/connection plug through hole in back of oven. I used needle nose pliers to guide electrical plug through hole. Disconnect old ignitor and plug in new. Simply pull apart. There is a guide key that will ensure you install plug correctly. Reasymble in reverse order. Hardest part for me was getting the door back one.

I removed the two rear screws securing the bottom plate inside the oven. The ignitor visually was fine, however the wires internally must have frayed and was not connecting properly. I unscrewed the two screws securing the ignitor, disconnected the plug, then reconnected the new ignitor and things fired up immediately.

I unscrewed the ignitor from the gas supply. Unplugged the ignitor. Plugged the new ignitor in and screwed it back in place to the gas supply. It could not have been easier!

Replace the igniter. Removed 2 rear screws that secure bottom oven pan. Removed pan. Ignigter is located in center rear by 2 screws. Removed the screws and pulled ignigter out from rear. There us a prong connection that when pressed will release igniter. Don't touch new ignigter without gloves on. Will reduce life. Plugged in new ignigter and secured w 2 screws. Turned on oven to ensure problem was fixed. After 30 seconds, oven ignited. Replaced bottom oven pan. Tadaa!

Removed oven door, removed bottom of oven, removed old igniter, installed the new one and plugged it in in the back of the stove. Installed oven door and it works fine. .

removed inside bottom of oven, removed 2 screws that held the ignighter, pulled out the oven, removed one screw on small cover, unpluged old ignighter, removed old ignighter, pusned the wires through the back of the oven, plugged ity in, attached the nerw ignighter, and replaced the cover/ and the bottom of the oven.
i teted the oven before i closed everything to insure it would light.

There are two elements to look at, one on top (broil) and one on the bottom (bake). Same element but may have different connectors. Double check before ordering.

Installing new igniter was very easy. The problem I had was removing the screws. The range is 18 yrs old. The screws were stuck from yrs of use. Especially in the oven cover plate. I used w- d 40 it didn't work. I decided to take a 2" putty knife and push it under the screw head to release it and it worked. They came right out. The igniter screws were also difficult to get out. Once those were removed, I pulled the stove out, turned off the gas and the electrical plug, removed back plate unplugged the old igniter and connected the new one. Easy, peasy. Turned gas on etc. Tested the oven to be sure it worked. Turned oven off.Then put it all back the way it was. Done! The igniter install was simple and qiuck. The time problem was the screws.

same as taking out old part and i misdiagnosed the problem ordered wrong part first and parts select steered me ito the correct part thank you