This switch controls the stove top surface burner.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Cooktop, Range.
This part works with the following products:
KitchenAid, Whirlpool.
Part# WP4456027 replaces these:
4456027
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
4.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
1
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
William M - April 21, 2020
Verified Purchase
Worked fine but needed small wiring modification
One of the connecting wire spade lugs was smaller than the one on the switch. No big deal if you have the proper lug and crimping tool...which I have but that would stop some people that don't work with electrical wiring.
★★★★★
★★★★★
TERRY Y - October 6, 2018
Verified Purchase
Great replacement
The part is exactly as advertised. Works great . The short delivery time is amazing
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David
September 18, 2017
For the dual burner the center element does not work. It seems as though the most common issue with an element not working is the relay switch. Is this the relay switch for the dual burner (right rear center eye))?
For model number KECD806RBL02
Hi David,
Thank you for the question. The Dual Burner Control Switch part number is PartSelect Number PS11742653. I will also recommend testing the element its self to see if the middle part may have become defective.
Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Philip
October 12, 2017
The left front, largest diameter dual burner will not turn off the outer ring when the knob is turned to low. The entire burner stays hot.
For model number KECC502GBL0
Hi Philip,
Thank you for your question. I would suggest checking your switch and your burner. It could be either of those parts that are causing your issue. Good luck with your repair.
Was this helpful?
Thank you for voting!
Tom
February 25, 2018
I recently bought a used KitchenAid stove and the front left burner is a dual burner and only the outside ring works. I took the oven apart and switched the wires on the burner and the inside burner would work. My question is should the switch only have one wire on the p1 slot or is this switch wired wrong? Or is it the switch itself bad? Thanks
For model number KESK901SSS05
Hi Tom, Thank you for the question. Each terminal should only have one wire each. I recommend replacing the switch its self. Hope this helps!
Was this helpful?
Thank you for voting!
Mike
November 7, 2019
One of the element switch ( knobs) does not turn on the element - it feels like it doesn't want to turn freely - like a default safety has been activated ? Any ideas of repair and which part? Thanks very much michael
Hi Mike, thank you for your question. Be sure to cut power to your appliance and remove any parts before doing tests. There are a couple of parts that could cause this issue specifically. You will need a multi meter to be able to test the parts. The first part you will want to check is your element. It should be reading between 0 - 50 ohms to be working correctly. The other part to check would be your infinite (or surface burner) switch. When you remove that part from the appliance, connect each probe from your multi meter to the prongs and then turn the switch to an on position. If you get no continuity then the switch is the issue. It could also be your wiring that is the issue but you should see visual damage on that part in most cases. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
Jeff
October 26, 2021
Right front dual burner does not stay on. It will stay on for 5 seconds and turn off by itself and so on.
For model number WCE55US0HB
Hello Jeff, Thank you for the question. This could be a defective Burner Element, Bad connection tot he Control Switch or defective Switch. We suggest unplugging the appliance and checking the wiring from the switch to the Burner Element. You can also test the element with a Multi Meter and if good, replace the Switch. We hope this helps!
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11742653
Manufacturer Part Number: WP4456027