Average Repair Rating: 2.5 / 5.0, 2 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Sparker would not quit sparking after lighting the gas.
Turned off the gas then disconnected the gas line. Unplugged the AC cord and removed the unit from the counter top. Had to locate a suitable area to lay the cooktop, rather large. The bottom cover is held on by 6-8 sheet metal screws, however, the gas regulator and nipple must be removed also for the cover to come off. I removed the Igniter module screws, leaving the wires connected and mounted the new module in it's place. I then removed one wire at a time from the old and put it on the new part. Replaced the back cover and reinstalled the gas regulator with fresh pipe sealant. Probably took an hour including cleaning the top and counter top.
Other Parts Used:
John from Waterford, MI
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Wrench (Adjustable)
35 of 46 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
spark module failure, wouldn't spark.
The repair was fairly straightforward, much easier the second time around. The first part was defective. (irregular spark). I reordered and installed the new one. It works, but nowhere near as good as the original.The problem is that the frequency of the spark on these replacement modules is only once per second. To get technical, the gas as presented to the spark is turbulent, causing several sparks to occur before the ideal mixture coincides with the spark. Needless to say, there is an excess of gas wafting around the kitchen until it lights, sometimes in excess of 20 seconds. NOT SAFE! Our BBQ and fireplace insert spark orders of magnitude faster than this.
Other Parts Used:
Bob from LAKEWOOD, CO
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench (Adjustable)
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert
February 21, 2018
What is the best way to located and replace the spark module? Is it located and replaceable from the back? Where is it actually located. Sorry for the repeated question!
For model number KGRT507BBL3
Hi Robert, Thank you for the question. The Spark Module is located at the back on the lower right side. You should be able to see it once the back panel is removed. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
March 16, 2018
Ordered and installed new spark module including installation instructions for exchanging original p/n 4173501 with 44543932 (eaton). Followed instruction exactly wire for wire but there were no spark to any burner. Is there any way to check new module for output?
For model number KGCT365B
Hello Robert, Thank you for your inquiry. You can test it with a multimeter. Hope this helps!
Was this helpful?
Thank you for voting!
Richard
January 30, 2020
How do i troubleshoot this model. There are no troubleshooting manuals on the internet that i can find. My problem is that this unit sparks all the time, even when the burner is lit. How do i conclude that the spark module is my problem and not another component.
For model number KGCT305TBL0
Hello Richard, One of the spark ignition switches may be faulty. The spark ignition switch sends voltage to the spark module. When the electrical contacts inside the switch close, power flows to the spark module. If the spark ignition switch fails with the electrical contacts closed, the switch will send continuous voltage to the spark module. To determine if any of the spark ignition switches is defective, use a multimeter to test each of the switches for continuity. If a spark ignition switches shows continuity at all settings, replace it. I hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11742616
Manufacturer Part Number: WP4454392