Average Repair Rating: 3.3 / 5.0, 2 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Hot water not flowing through.
I removed the screws (as they became accessible) from the following items with screw driver or nut driver: 1) door 2) hinges 3) hinges vanity plug on the other side of the door 4) front panel
I then 5) unplugged the washing machine 6) turned off the hot and cold water 7) removed the hoses and hung them up to avoid water on your floor (have mopping cloth available) 8) Removed the detergent and softener storage pockets 9) Opened the top of the washing machine. 10) pull out internal hoses away from the water valve 11) Removed spade electrical clips from the valve. 12) Wiggle away the valve and remove (if screw is present removed it as well) 13) Put in the new valve and reverse the process back to item 1.
It appears that there was mineral deposit on the valve and I am not certain if it clogged up the valve or seized it .
Other Parts Used:
Lindy from Columbus, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench set
12 of 17 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water valve stuck open, unit leaked
Removed door, removed top from front clips, removed front, removed screws holding water distribution box, lifted top, removed valve, replaced valve. Reversed procedure to reassemble.
Other Parts Used:
PHILIP from SHERMAN, TX
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
7 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lance
August 2, 2017
Washer fills up with water when sprinklers turn on.
For model number MAH55008WW
Hi Lance,
Thank you for the interesting question. Sounds like the Water Valve opening with the water pressure within the waterlines. I suggest replacing the Water Valve, Part number PS11739418
3 people found this helpful.
Was this helpful?
Thank you for voting!
Mark
January 17, 2018
Washer will not stop filling with water. I tried starting it, then unplugged the washer. It stopped filling.
For model number MAH5500BWW
Hi Mark, Thank you for the question. I suggest testing or replacing the Water Inlet valve.When the valve is stuck open it will allow water through even when it is not on the fill cycle. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Charlotte
June 18, 2019
Ordered wp22003834 and our part has 4 valves. What part # should we have ordered? Getting nf code. The hot water comes in ok but no cold.
For model number mah5500bww
Hi Charlotte. Thank you for your question. If you are looking for your 4 coil valve then this part you have questioned on would be the part for your model number. Good luck with your repair.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
