If the resistor is burned on the board, that indicates there might be another problem.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
Maytag.
Part# WP22002989 replaces these:
AP6006334, 22002788, 22002989, 22002989R
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 2 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Intermittent fill, rinse, door lock, and temp control.
Removed five screws from rear of control panel. Removed two control board mounting screws. Replaced control board. Replaced all screws. Washer worked except for temp control. Opened front door and removed four screws. Removed front panel. Removed two lock tab screws and locking tabs. Lifted up top of washer. Unplugged cable from thermistor. Closed washer top and reinstalled locks and front panel. Temperature control switch now controls temperature without using the thermistor+.
Other Parts Used:
Stephen from Amity, OR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
19 of 26 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water Pump not draining water; Mother Board burned out with power outage
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Orrin
March 22, 2018
The part replacement description says that if the resister is burned out that it's a sign of some other problem - what is the other problem? The resister on my control board is burned out thank you
Hi Orrin, Thank you for the question. I suggest testing the interlock switch, PartSelect Number: PS11739429 and the Washer Pressure Switch, PartSelect Number: PS11739398 with a multimeter. If they are good then you will need to test the Tub Displacement Switch, PartSelect Number: PS11739324 and the Door Lock/Spin Enable Switch, PartSelect Number: PS11739335. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Phil
July 10, 2019
Replaced pump motor after nd code; pump ran for a test cycle then nd code again. Control board next? I am also trying to find a service manual for this machine.Sn shows date of manufacture of 2/2006. should i just move on or save?
For model number MAH8700AWM
Hello Phil, Thank you for the question. Before replacing the board I suggest checking the drain house to make sure there is no blockages. Hope this helps!
Was this helpful?
Thank you for voting!
Anne
December 14, 2023
Washer will turn on and you can set a cycle but the door won’t lock then it just sounds like it’s trying to drain then F6 and E3 codes come up. Washer only two years old. Have unplugged fiddled with wires nothing looks burned what do I need
For model number MHW8630HC3
Hello Anne, thank you for the question. According to our research, the F6E3 error code indicates there is an issue with the appliance control unit, user interface or associated wiring. We would recommend checking the control panel, part number PS12717540, to fix the issue. We hope this helps!
Washer does not stop filling all cycles, over flows on wash and rinse. Water stops when stop button is pushed. Replaced door resistors 6 years ago, replaced water input valve last week did not fix problem. Checked input water 75 psi, pump and spin work fine.
For model number MAH4000AWW
Hi Ken,
Thank you for your question. If the washing machine will not stop filling with water, you will need to check the water inlet valve and the washer pressure switch. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
