Average Repair Rating: 4.9 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
machine was showing all lights and wouldn't start up
unplugged machine removed front panel .disconnect wiring harnesses . pop out old control ,install new reconnect wiring put back in place resecure and plug in and test
Other Parts Used:
Angel from MILWAUKEE, WI
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jim
October 22, 2017
All the lights are on at the same time and the washer won't start
For model number CAE2743BQ0
Hi Jim,
Thank you for your question. You could try unplugging your appliance from the power for about 5 minutes and then plugging your appliance back in again. If you still have the problem, then you will need to replace your control board. Good luck with your repair.
6 people found this helpful.
Was this helpful?
Thank you for voting!
Brent
February 14, 2018
Lid lock keeps flashing and i can hear clicking but won't lock and machine stays in sensing mode
For model number CAE2743BQ0
Hi Brent, Thank you for the question. This means the lock switch is defective and the lid lock needs to be replaced. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Drew
December 10, 2019
The “sensing load” light comes on, and the washer begins to fill with water, but the water only runs for about 20 seconds and then stops. When the washer was empty it ran through a whole cycle except for the final spin, but with a small load in it the machine won’t go past “sensing load”. That light went out after about 10 minutes, and about five minutes after that the discharge pump came on and ran for about 5 minutes. Only a small amount of water came out, and i checked hose for blockages. After the pump shut off the “sensing load” light, the “rinse” light and the “done” light all came on at the same time. Any ideas?
For model number CAE2743BQ0
Hello Drew, thank you for your question. It sounds like there may be an issue with the pressure switch or pressure hose. We would recommend replacing those parts first. The pressure switch is part of the board PartSelect Number PS11737994. If the issue persists, the problem could be with the lid switch. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Bridgette
September 27, 2017
I'm trying to find the serial number and p/n number for the above model for the main control board
For model number WTW4880AW0
Hi Bridgette,
Thank you for your question. I have attached the link to the part down below for you. Good luck with your repair.
I used to have the issue where, after a load, all lights would be on and the machine would eat quarters and not start until after the machine was reset via diagnostics mode. I replaced the control board, and the machine worked flawlessly for maybe six months, but now it's having the same issues again, but worse. It seems like the machine needs to be reset twice and then it works again. What could the issue be?
For model number CAE2743BQ0
Hello Kenny, thank you for getting in touch. Based on our understanding of the issue, we would suggest you checking the control panel, part number PS7320635, to fix the issue. We hope this helps!
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
