Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lydia
October 21, 2017
I need a side vent kit, will the #10704365 kit work for this model
For model number wgd800dw
Hello Lydia, thank you for contacting us. The correct part number for the side exhaust kit for your model is PS3633049. Good luck with the repair!
Will the W10704365 side venting kit work with this dryer? We have been unable to locate anyone that has the W10323246 4-way vent kit available.
For model number WGD6620HWH
Hi Tom,
Thank you for your question. The side vent kit, part number W10323246 is available. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Donna
November 11, 2022
Is W10704365 just the one tube as the diagram shows or is it the full kit (12 pieces) ?
Hello Donna, thank you for your question. This is a full kit of 12 pieces. We hope this information will help you.
Was this helpful?
Thank you for voting!
David
September 5, 2023
Do you have to disassemble dryer to add side vent kits?
For model number Medb835dw4
Hello David, thank you for reaching out. You may follow these instructions to add the side vent kit. These may not be of the exact same model, but will help you with the process:
Make sure the power cord is unplugged, and the venting is detached from the dryer exhaust outlet. Use a nut driver to un-thread the rear screws securing the top panel and bracket. Un-thread the screws securing the control housing. Disconnect the control panel wire connector from the control board. Lift the control housing and panel up and out to remove. Disconnect the door switch wire harness. Lift up the front of the dryer. Use the nut driver to loosen the middle screws. Remove the support and lower the appliance. Open the dryer door and use a screwdriver to un-thread the screws securing the front panel to the bulkhead. Use a nut driver to un-thread the top screws. Lift the front panel up and out to remove. Un-thread the screws securing the control housing bracket. Un-thread the screws securing the front of the control board bracket. Lift the control housing bracket up to remove. Disconnect the moisture sensor wire harness. Un-thread the screw to release the lower retaining bracket. Un-thread the screws securing the front bulkhead to the frame. Lift the bulkhead up and detach it from the drum and frame. Push the idler pulley to release the tension on the belt. Un-thread the belt from the pulley and motor shaft. Un-thread the screws securing the outlet vent to the blower housing. Slide the vent out. Depress the tabs to detach the plastic vent ring. If you need the venting to exhaust out the left or right side of the cabinet, use a hammer and chisel to break the retaining tabs securing the rear knockout cover. Fully detach the cover. If exhausting through the dryer base, you will need to add the small extension vent piece in order to align the elbow section with the hole. Insert the elbow section into the long vent and secure with the clamp. Place another clamp over the end of the elbow section. Now insert the long vent through the hole in the cabinet or base and align the elbow on the vent piece attached to the blower outlet. Tighten the clamp. At-least 10 inches of space should be between the wall and the cabinet when installing side venting. Slide the plastic ring over the long vent piece and snap it into place in the hole. Cover the old rear exhaust hole by positioning the tab of the provided metal cover plate in the opening from the inside. Now follow the same instructions to reassemble the dryer.
We hope that helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Our scratch-free, streak-free formula removes fingerprints, smudges, grease, dirt and oil, while protecting and polishing to repel dust and dirt. Use on all stainless steel appliance brands and surfaces. Stainless Steel ...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS10065965
Manufacturer Part Number: W10704365