Nailer Parts

Nailer Flat Washer Genuine Makita replacement part, it is sold individually. This washer is used in various areas in the tool model numbers shown below. It is used as a washer for a screw or bolt or even as a spacer.

Nailer Washer-rubber-7 This rubber replacement seal is designed for use with select pneumatic and coil-fed nailers, providing a tight and reliable seal at the nose of the tool. Its primary function is to prevent air leakage during operation, helping to maintain consistent pressure and performance. Over time, seals can wear down or become damaged, which may lead to reduced efficiency or tool malfunction. This part is sold individually and is ideal for routine maintenance or repair. Replacing a worn nose seal can help extend the life of your tool and ensure smooth, dependable operation.

Nailer O Ring 21 This o-ring 21 is an OEM part direct from Makita. The flexible plastic ring is made for use with pneumatic nailers and rotary hammer tools. This item is often fitted between the compression spring and the driver, providing protection from friction. The o-ring 21 is sold individually. You will need a hex key for the repair.

Nailer Urethane Ring 3 This replacement urethane ring is a high quality item that is specially designed for Makita nailers. The purpose of this item is to create an air-tight seal for the pushing lever, for correct application make sure to check appropriate diagrams of your unit. Over time rings and seals will shrink, become brittle and crack eventually requiring a replacement. It is made from durable rubber and it is sold individually.

Nailer O-ring 5 O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> - O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

Nailer Compression Spring 4 This is an authentic replacement part manufactured for use with Makita pneumatic nailers and jigsaws. The special compression spring is used with different types of equipment and the application of the spring varies depending on the model of equipment. This compression spring is available as an individual replacement part, please see model diagram for part location and usage.

Nailer Switch This replacement switch is a high quality item sourced directly from original equipment manufacturer. It is specially made for used on Dewalt and Porter Cable power tools. It is the part that allows user to turn the tool on and off. These mechanical switches will over time wear our and fail requiring replacement. It is made out of durable plastic material and it is sold individually. No tools needed to replace this switch, it is secured with a pair of tabs on each side.

Nailer Driver, Xtp01

Nailer Flat Washer 5 This item is a genuine Makita part that has been sourced from the original manufacturer to be used with trimmers, circular saws, sanders, routers, nailers, reciprocating saws, laminate trimmers, and planers. The flat washer is used with different types of power tools and the application of the washer can vary based on the model of the equipment. This item is available as an individual replacement part.

Nailer Nose Adapter, Af505n The nose adapter is a genuine Makita replacement part that has been OEM sourced to ensure a high level of quality. This item is intended to be used with brad nailers. This part attaches to the contact arm and is used to provide a stable connection between the contact arm and the material being nailed. This part also prevents marring on the surface of the trim being fastened. This part is sold as an individual replacement part.