ZDP364NDN1SS General Electric Range - Overview
Sections of the ZDP364NDN1SS
[Viewing 9 of 9]
Keep searches simple, eg. "belt" or "pump".
Range Foot Grate
PartSelect #: PS3654144
Manufacturer #: WB02K10364
Introducing the robust GE Foot Grate, carefully designed to keep your cooktop smooth and damage-free. Constructed from premium materials, this sturdy burner grate pad sticks effortlessly to the bottom...
$19.99
Special Order
Door Handle Fastener
PartSelect #: PS6447735
Manufacturer #: WR01X11007
This is a door handle fastener to secure the handle to your refrigerator drawer. It is also known and a mounting bolt or screw. It is approximately 1 inch in total length, and is made of metal.
$17.70
Special Order
Halogen Lamp
PartSelect #: PS1018917
Manufacturer #: WB25T10064
If your appliance is starting to dim, the GE Lamp Halogen might just be the solution you need. This 20-watt light bulb not only brightens up your appliance, but also ensures it works at its absolute b...
$32.93
Special Order
FRAME GRATE Assembly
PartSelect #: PS3503826
Manufacturer #: WB31K10253
You're looking at the GE Surface Burner Grate Support Frame, a top-notch replacement part specially built for your GE range. This support frame is what keeps your burner grate secure and steady, provi...
$377.38
Special Order
GRATE
PartSelect #: PS3503825
Manufacturer #: WB31K10252
This cast iron burner grate gives your cooktop a sturdy, stylish upgrade. It holds pots and pans securely over the flame and spreads heat evenly for better cooking results. The smooth gray finish look...
$226.12
Special Order
Burner Cap (18k)
PartSelect #: PS16762391
Manufacturer #: WB29X43469
This burner cap replaces a worn or discolored cap on high-output burners, helping ensure even heat distribution and reliable cooking performance. Designed for 18,000-BTU burners, it’s a direct drop-in...
No Longer Available
KNOB Assembly
PartSelect #: PS8753584
Manufacturer #: WB03K10359
Struggling with a broken knob on your GE range? Get it fixed quickly and conveniently with our GE Surface Burner Knob, a vital part for your kitchen stove. Known as a thermostat knob, this handy piece...
$86.53
Special Order
Common Symptoms of the ZDP364NDN1SS
[Viewing 3 of 3]Will Not Start
Fixed by
these parts
these parts
Show All
Door won’t open or close
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
terminal block melted
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient
Parts Used:
-
jonathan from willow springs, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
56 of 77 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original terminal block plastic shielding melted, protecting appliance when the wires overheated.
Safety first * Unplugged 220 VAC from outlet. Removed shield cover screws with 1/4" hex nut driver (5 screws). Removed all 6 silver screws from terminal block with 1/4" nut driver, freeing all wires. Removed the green ground screw and ground bracket from center terminal. Cut away (using the drill) melted original terminal block plastic to access the 2 black 1/4" nuts holding original terminal block onto appliance. Discarded the original damaged terminal block. Attached the new terminal block, aligning the mounting holes and the terminal block the same way the original terminal block was lined up and re-used the black 1/4" nuts (original used because the replacement package did not include new black screws). I bought a new appliance cord, since the original cord overheated. Reattached all wires using the 6 new silver screws. Start with the middle terminal by attaching the appliance wires and the ground bracket. The ground must be attached to the bracket and the bracket bridges between the terminal block and the range body. Reattached shield cover. Plugged in appliance. Note: it doesn't matter which outside wire attaches to the outside terminals (both are hot), but the middle wire (neutral) must attach to the middle terminal. However, the ring terminal should be flush on the terminal block so you don't bend the ring.
Parts Used:
-
Brian from DOVER, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
6 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I broke the frame gate assembly by sitting on it. I ordered a new on and put it on. No tools required
I threw the old frame away and placed the new one on top of the stove
Parts Used:
-
William from UPPR MARLBORO, MD
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!