If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
$17.11
In Stock
Order within the next 8 hrs and your part ships today!
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.20
In Stock
Order within the next 8 hrs and your part ships today!
This is a genuine OEM part. The push-to-start switch is composed of metal and plastic components. Compatible with dryers, the Whirlpool switch powers the appliance after the button is pressed. With a ...
$25.47
In Stock
Order within the next 8 hrs and your part ships today!
Order within the next 8 hrs and your part ships today!
Questions And Answers for YWET4024HW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Delmann
March 16, 2023
M'y wash deosnt spin
For model number YWET4024HW0
Hello Delmann, thank you for getting in touch. We have concluded that the issue is with the drive belt, pulley, and drive motor. We suggest checking the drive belt. The easiest way to test this out is to open the drum and turn it by hand. A healthy drive belt should provide some resistance as you spin it. If there is no resistance, the drive belt is faulty, and you need to replace the drive belt, part number PS11765551. Also, check the drive pulley. If found defective, replace the pulley, part number PS11765550. If these do not solve the issue, replacing the drive motor, part number PS12348811, will help you fix the issue. We hope this helps, good luck with this repair!
When the water enters the tank at first everything is fine. after a few minutes, the water begins to stop flowing and starts again. It happens quickly as if a valve was trying to quickly control the flow. during the second cycle for rinsing. it does the same thing.
For model number YWET4024HW0
Hello Marc, thank you for getting in touch. Based on the description that you have provided, we would recommend checking the control board, part number PS12348800, to solve the problem. We hope this helps!
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils. Not knowing what the problem was I started looking at the coils and could not see any broken parts. So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading. I replaced with a new one and put it all back together the way I took it apart. Then I plugged it in and it worked first time, I now have warm dry clothes.
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.
Ascertaining the problem was the most time consuming part.
The actual repair was quite simple and didn't take but 15-20 minutes.
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.
