WZF34X20DW05 Whirlpool Freezer - Instructions

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

The repair seemed simple, I just needed to remove the old bracket -- 4 screws -- and slip the new one on.

The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes, I needed to shim up the side of the fridge that I was working on.

To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.

Took the new kick plate out of the box. Snapped it into position. I have had a repairman for this refrigerator before. I would rather repair an appliance than buy a new one. I'm very proud that I thought to get a replacement part myself instead of calling my friendly repairman again. Saved a few dollars.

snap the new one in place.

Just put it into the bottom of the fridge and it snapped into place. NO PROBLEM AT ALL.

Bought a new psrt

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.

No tools required, but you must be careful not to shove or jam this kick plate into place as it is a plastic part and not really very sturdy. This is the second time I have replaced the kick plate and PartSelect has always been knowledgeable, polite, and helpful
!!

I unplugged the unit Frist. Then I removed the grill covering the compressor and fan from the back. I then located the rear wheel and pin. I bent down the retaining tab and removed the pin and wheel. I installed new wheel and pin and bent retaining tab back to origional location. Replaced grill and checked unit for proper operation.

remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed approx 3/4" under edge of refrigerator.

To clip it in was easy. The hard part was getting down to do it. I'm 78, hubby is 80 and because of the fridge width it took both of us since we have a bottom freezer drawer. We don't get down or even up very well anymore. The part fit fine and looks great. The part arrived in less than 24 hours which pleasantly surprised us. Thanks much.!