This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This is a genuine replacement light bulb for a refrigerator. The inside of your refrigerator should illuminate when you open the door. If your fridge does not illuminate, you may need to replace this ...
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
This temperature sensor is for refrigerators.
The temperature sensor senses the temperature inside the refrigerator and sends information to the electronic control.
Unplug the refrigerator and s...
If your refrigerator or freezer is too warm, or making noises, you may need to replace the fan blade. The fan blade attaches to the evaporator motor, which is in the freezer section, to help circulate...
Experience the simple solution to a wobbly refrigerator with the Whirlpool Refrigerator Leveling Leg. This authentic, factory-made part is designed to keep your refrigerator stable and even, saving yo...
The compressor run capacitor keeps the refrigerator motor running smoothly. Be sure to unplug the appliance before installation and verify the part number for compatibility.
Is your refrigerator not cooling like it used to? The Whirlpool Refrigerator Temperature Sensor might just be what you need! This is a dependable thermistor, which plays an important role in maintaini...
$85.20
In Stock
Questions And Answers for WZF34X20DW01
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
STEPH
September 8, 2025
I think I need a defrost sensor ( not sure what it’s called.…) because my freezer keeps freezing over on the coils and I already replaced the element.
For model number WZF34X20DW01
Hello Steph, thank you for contacting us. The defrost sensing or cycles in your refrigerator is controlled by the control board assembly, part number PS16620033. Before replacing the control board, we suggest checking the drain system and make sure the drain is not blocked. Also, check the door gasket, part number PS16221231. If the door is not sealing properly, it can cause warm air to enter the refrigerator, which can result in condensation or ice buildup. We hope this information helps!
I just purchased this model stand-up; freezer. Can i purchase additional shelves for theh unit.Thanks
For model number WZF34X20DW01
Hello Paul, Thank you for your inquiry. We have researched the model number you have provided and there are two shelves available for your model, the upper one part# PS12731205 which measures 27-1/2 inches by 15-3/4 inches and the lower one PS11701774, which also measures 27 1/2 inches but is narrower from front to back. We hope this helps.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
The repair seemed simple, I just needed to remove the old bracket -- 4 screws -- and slip the new one on.
The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes, I needed to shim up the side of the fridge that I was working on.
To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet.
