This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.20
In Stock
Order within the next 12 hrs and your part ships today!
This kit includes one driver hub and two driven basket hubs. The basket hub is located under the agitator. If your washer is not agitating or spinning properly, the hubs will need to be replaced.
$48.11
In Stock
Order within the next 12 hrs and your part ships today!
This part makes sure that the lid is shut before allowing the machine to start or agitate.
NOTE: This is a manufacturer substitution. Part may differ in appearance but is a functional equivalent to prior parts including
$121.09
In Stock
Order within the next 12 hrs and your part ships today!
This rotary position sensor is a genuine OEM part for your washing machine. It helps to ensure the load of clothing stays balanced during the wash cycle. Customers have rated this repair as easy. To c...
$56.04
In Stock
Order within the next 12 hrs and your part ships today!
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
$11.68
In Stock
Order within the next 12 hrs and your part ships today!
This is a replacement lid hinge for your washer. It is approximately 2.5 inches in length and 1.5 inches in width. The lid hinge is what the lid for your washer pivots on. If the lid hinge is damaged,...
$10.20
In Stock
Order within the next 12 hrs and your part ships today!
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$194.18
In Stock
Order within the next 12 hrs and your part ships today!
Order within the next 12 hrs and your part ships today!
Questions And Answers for WTW8000BW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
14 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Aaron
September 14, 2023
Does the water inlet valve fix the issue of the washer only washing with hot water? If not what other part would it be?
I am having an issue where the washer is only washing with hot water even when the setting is set to cold
For model number WTW8000BW0
Hello Aaron, thank you for your question! This can happen if the hot water line is mistakenly connected to the cold water inlet on the washer, and vice versa. Double-check the water supply connections to ensure they are properly aligned with the designated inlet valves. If this is not the issue, the problem could be with the faulty water inlet valve, part number PS11731257. We hope this information is useful!
Hello, so the plastic piece that comes out to lock the lid broke off so now the lid doesn’t lock it open and doesn’t open it locked. Do I need a whole new lock assembly kit or is there something else I need to buy?
For model number WTW8000BW0
Hello Aimee, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11756782. The strike is only sold as part of the Lid Lock Assembly. Hope this helps!
How do you open the top panel from the cabinet to replace the basket seal and bearings?
For model number WTW8000BW0
Hello Bill and thank you for writing.
Unplug the machine. If there is a fault with any aspect of your washing machine and you are going to get inside the machine, then there is no reason to risk the possibility of an electrical shock. The machine may have to be pulled away from the wall slightly to remove the wall plug.
Lift up the door of your top-loading machine. Look on the right side of the door opening where the door would be if it were closed. Here you should find two Phillips screws. Remove them and set them aside in a safe place. On a few models of top-loading machines, the two Phillips screws holding the top in place will be on the left side where the door would be when it is closed. Lift up on the front edge of the top of the machine. It may be sticky, but with a little effort the front of the top of the machine should lift up, like a clamshell. Lift it until it stays up by itself or until a small metal pole becomes visible which will hold the top up and out of the way. We hope this helps. Please contact us anytime if you require further assistance.
Was this helpful?
Thank you for voting!
Rediat
January 21, 2020
I have a Whirlpool Cabrio washer. I try to wash, the water came on and stop. Try to start wash and a flashing F light came and the machine will not wash.
For model number WTW8000BW0
hello Rediat, Thank you for the question. The F code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen. Normally the Lid Lock, PartSelect Number PS11756782 will need to be replaced. We hope this helps.
Your answer to bill on how to raise the cover lid. My machine does not have two phillips head screws on right or left side.
For model number WTW8000BW0
Hi Keith,
Thank you for your question. Here is a link to a video from our website that you may reference on how to raise the top panel on your washer, https://www.partselect.com/PS11756782-Whirlpool-WPW10619844-Lid-Lock-Assembly.htm?SourceCode=21&SearchTerm=DE512&ModelNum=WTW8000BW0&pSearchTerm=lid%20switch. The washer in the video may not show exactly like the one you have and the part being installed is the lid switch, but it will give you a general idea on how to raise the top panel. If you require more information, please check out the link to our YouTube Channel on our website for more videos that may help you. We hope this helps. Thank you and have a great day.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed a cap in the center of the tub basket which has a bolt that needs removed I believe it's a 9/16 after I removed the bolt I then removed the center of the bottom of the basket assembly which then allowed me to get to the basket hub that needed replaced it was a little dirty and I couldn't get it out so I sprayed a little penitrating oil on it let it sit a little then I was able to remove the hub and install the new one then I put it all back together and the washer is working great
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Remove agitator and replace hub. I also recommend replacing the Suspension too. I could tell the hub was bad the piece of metal washer on the bottom was gone. The suspension lost a lot of its stiffing